Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0494
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: STD-120200
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-2870
Effortless Wire Stripping and Twisting: Saves time and reduces hand strain with fast, automated operation. Universal Compatibility: Works with various wire sizes for maximum versatility in your projects. Durable Construction: High-quality steel construction ensures long-lasting performance. Drill-Powered and Manual Operation: Offers flexibility for both...
Reference: RBD-0708
Large LCD display shows big Digital Numbers Temperature, Humidity and Time can be seen simultaneously. It has Stand to use as table-top or Hook for placing on the wall. Integral-hour alarm function Time, Date & Month display Low Power Consumption
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-0664
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1057
Low current leakage Light Weight and Offers good grip General purpose for all electronic applications. Advanced Heating element High-Quality Nickel-Copper plated Bit Quickly attains the working temperature Constant Tip temperature
Reference: RBD-1523
Microcontroller: ATmega328P Circuit Operating Voltage: 5V Clock frequency: 16MHz. 6 PWM port: D3, D5, D6, D9, D10, D11. Use For Atmel Atmega328P-AU microcontroller. Support serial download. Support 9V battery. A pair of TTL level serial port transceiver : RX / TX.
Reference: RBD-1947
Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg...
Reference: RBD-1948
Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off Note: Relay might be...
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-0323
Microcontroller ATmega328 (SMD) – Interface CH340G Operating Voltage: 5V Input Voltage (recommended): 7-12V Digital I / O Pins 14 (of which 6 provide PWM output) RoboticsBD Analog Input Pins: 6 A programming cable is included.
Reference: RBD-0155
Microcontroller: ATmega328 Circuit Operating Voltage: 5V Clock frequency: 16MHz. Digital I/O Pins: 14 8 analog input port: A0 ~ A7. A pair of TTL level serial port transceiver : RX / TX. 6 PWM port: D3, D5, D6, D9, D10, D11. Support serial download.
Reference: RBD-1159
Removes all Solder Residue Low cost and high-quality Ideal replacement for the old sponges. Removes excess solders from soldering iron tips Provides extended tip life
Reference: RBD-1757
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity: X: 28.6 LSB/g. Y: 31.2 LSB/g. Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection.
Reference: RBD-1690
ON/OFF switch button on the power adapter. Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-1322
Brand Name: KOOCU Model: V900 soldering iron Output Temperature: 200-480 degree Celsius Output Power:25W
Reference: RBD-1309
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.
Reference: RBD-0914
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
Reference: RBD-1374
Model: AM2301. Supply voltage: 3.3 ~ 5.2 V DC. Signal output form: Digital signal output. Temperature measurement range: -40 ~ +80 ºC. Temperature measurement precision: ± 0.5ºC Humidity range: 10%~90%RH. Humidity measurement precision: ±3%RH.
Reference: RBD-1533
Motor Type: NEMA23 Material: Mild Steel(MS). Dimensions: 50x62x64 (LxWxH) mm Mounting Holes Size: 5mm Weight: 90gm.
Reference: RBD-1165
9 Layer Acrylic stylish case with access to all Ports on pi 4 Compatible for All variant of the Raspberry pi 4 Model B Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel
Reference: RBD-2247
Onboard STM8S103 high-performance microprocessor With digital tube display Valid Measurement Distance: 3-400cm Display Unit: cm Maximum Input Voltage: 5VDC 2.54mm White Socket: 5V power interface.
Reference: RBD-2618
Precise & Comfortable Soldering: 60W power for efficient soldering & ergonomic handle with light and non-slip grip for comfortable use. Fast Heat Up & Safety: High-quality ceramic heater ensures quick heating & burn-proof silicone cable provides safety. Durable & Versatile: Ideal for electronics, computer repair, watchmaking, and other...
Reference: RBD-1144
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin Type A Japan Output Plug: Type C
Reference: RBD-1598
Material: Polyimide Spindle Type: Roll Tape Length: 33m TapeWidth: 50mm Colour: Metallic Brown Temperature Range: 200ºC
Reference: RBD-1874
Suitable for DIY & Hobby Kits, Routers, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-1879
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: NBSB24120200VU Brand: Motorola