Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-1180
Standard For Shield interfaces and shape Can continue to stack other For expansion boards 3 M3 screw positioning holes for easy installation High Drive (5V or 3.3V) normally open contact closure Onboard relay indicator (red) Note: Relay might be different from the picture as per stock
Reference: RBD-1368
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-1753
Digital I2S interface with high precision 24-bit dataHigh signal to noise ratio is 61 dBAHigh sensitivity – 26 dBFSStable frequency response from 60 Hz to 15 kHzLow power consumption: low current consumption 1.4 mAHigh PSR: -75 dBFS
Reference: RBD-2044
Model: ESP32-CAM-MB Color: Black Chipset: CH340G Connectivity Technology: USB Note: The camera module is not included with the board.
Reference: RBD-2075
MQ-2 Smoke Gas Detector Sensor ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts
Reference: RBD-2249
Made From High-Quality Materials. Electronic High-Frequency Oscillations (2.4MHz). Material: Ceramic, Wire Diameter: Atomizer: 2cm/0.79in; Sealing ring: 2.5cm/0.98in
Reference: RBD-2293
801S is a vibration sensor with a gold alloy plated shock sensor and an onboard comparator IC. The sensor is capable of providing real-time vibrational data along with micro shock detection and about 60,000,000 times shock guaranteed. Pin Type Pin Description VDD Voltage Input pin GND Ground terminal D0 Digital Signal Output pin A0...
Reference: RBD-2296
Features:This product is a booster coil production suite, the circuit is simple and reliable, with professional line drawings, electronic research convenience enthusiastsUses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high-frequency arc, elevated...
Reference: RBD-2302
Low Standby Current. 1-to-8 Bidirectional Translating Switches. I2C Bus and SMBus Compatible. 5-V Tolerant Inputs. Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II. Note : Product may vary in two variants TCA9548A & PCA9548A
Reference: RBD-2304
This is the 24 LED NeoPixel Ring, a small chainable 86mm outer diameter board equipped with 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver chip is located inside the LED. Each NeoPixel Stick has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and requires 5 V.
Reference: RBD-2306
The 12 Bit RGB LED Ring Module with Integrated Drivers – WS2812B can be used in colourful curtain-up/ flow water/raindrop/jump flash and so on hundreds of lighting effects. There is a single data line with a very timing-specific protocol. It has trichromatic colour for each pixel and can complete 16,777,216 colours of all true colour displays, the...
Reference: RBD-2312
When it comes to adding colour to an electronics projects, these 4x4 NeoPixel Squares use WS2812 Addressable RGB LED’s to display up to 16777216 different colour combinations, with simple operations and built-in features to greatly enhance functionality. This makes them ideal as LED Displays for basic to intermediate Electronics projects, and despite...
Reference: RBD-2307
This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...
Reference: RBD-2316
1.Wide Analog Input Voltage Range: +/-5V2.Low “ON” Resistance: 80 ohm (type) at Vcc = 4.5V; 70 ohm (type) at Vcc = 6.0V; 60 ohm (type) at Vcc = 9.0V3.Logic Level Translation: to enable 5V to communicate with +/-5V analog signals4.Board Size: 30 x 19 mm
Reference: RBD-2340
2 Channel PWM Pulse Frequency Adjustable Duty Cycle Square Wave Rectangular Wave Signal Generator Module to generate square wave for experiment development. This is used to drive stepping motor drivers' square waves, Generate an adjustable pulse for MCU using, and Generate an adjustable pulse for controlling the relative circuit (PWM adjust lightspeed, etc).
Reference: RBD-2410
Retain the merits of the V4.0 version Laminated design PCB immersion gold processing technology IIC interface Bluetooth module communication interface SD card module communication interface APC220 wireless rf modules communication interface RB URF v1.1 ultrasonic sensors interface 12864 LCD string of line and parallel interface 32 servo controller interface
Reference: RBD-2421
Product name: Humidifier Driver BoardColor: As showVoltage: DV 5VCurrent: 300mAPower: 2WFrequency: 110KHzSize: approx. 46 *20*17mm/1.81*0.79*0.67"
Reference: RBD-2426
1.5V USB ultrasonic mist maker driver board and atomizer plate. 2. Low driving voltage, low power, low impedance, stable waveform, high conversion efficiency. 3. Round ring atomizer plate, middle spray, 5um ultra-fine spray aperture, 740 ultra-dense spray holes. 4. The surface of the atomizing sheet adopts an oxidation-resistant silver layer to protect...
Reference: RBD-2415
Dual PS2 Game Joystick Button Module Joystick Compatible With Arduino is a module use to connect and interface PlayStation 2 (PS2) game joysticks with an Arduino microcontroller board. It provides a simple and convenient way to control various projects and applications using PS2-style joysticks. The module consists of two PS2 joysticks, each with two-axis...
Reference: RBD-2442
8 channels can convert up to 8 logic signals Converts voltage levels between 1.2 to 3.6V and 1.65 to 5.5V systems Bi-directional with automatic direction control Each channel operates independently Optimized for open-drain applications like I2C, but can also work in push-pull applications Output enable allows outputs to be disabled
Reference: RBD-2444
Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink
Reference: RBD-2454
Power: 5V This module is compatible with 5V and 3.3V microcontrollers. Material: PCB + Electronic Components
Reference: RBD-2470
3 Watt 8 Ohm Mini Speaker for Electronics Project with JST-PH2.0 Interface
Reference: RBD-2546
The ADuM1201 is a dual channel digital isolator using technology by Analog Devices called iCoupler. It provides electrical isolation similar to an optocoupler and optionally provides logic level conversion between 3.3V and 5V systems.
Reference: RBD-2555
This is a self-contained switching module that energizes / de-energizes a relay based on the humidity level. Just add 5V power and hook up the load you want to control then adjust the potentiometer to set the relative humidity level at which you want the relay to switch between ON / OFF. This type of module can be used for applications such as to...
Reference: RBD-2557
Introducing the Battery Level Display Module, a versatile and user-friendly device based on battery-style digital tube LED technology. This module features 10 light segments and incorporates the TM1651 driver chip for simplified control, requiring only two signal lines along with VCC and GND connections. It is specifically designed for displaying battery...
Reference: RBD-2658
This 1 channel 12V 30A relay control board module with optocoupler modules is compliant with international safety standards, control and load areas isolation trenches it has a single relay a genuine. The inputs of 1 Channel 12V 30A Relay Module are isolated to protect any delicate control circuitry. It can be used as a single chip module for appliance...
Reference: RBD-2659
Trigger Voltage: 5VDC Switching Voltage: 250VAC@30A; 30VDC@30A The module can be set high level or low-level trigger by the jumper Note: Relay brand may vary from actual product as our stock rotates.
Reference: RBD-2718
Dual-Channel Stereo Output Run-on 7V to 15V power Supply 32 Steps DC volume control has a +32dB to -75dB range. 40 pin QFN 6 x 6 mm package. Much higher efficiency in terms of cost and performance than competitors’ ICs