Reference: RBD-0280

Mini Breadboard

78 reviews

Tie-points: 170 (10×17) Size: 48 x 35 x 10 mm(LxWxH). Use: experimental, testing, robot Matching jumper, diameter 0.8mm Phosphor bronze nickel plated spring clips Accepts a variety of wire sizes (29-20 the AWG) **1 pcs Random Color

Reference: RBD-1686

Brand: RoboticsBD

4v 2000 RPM DC Motor

4 reviews

Operating Voltage: 3 to 6VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 10mm(approx.) Weight; 15g(approx.)

Reference: RBD-2076

5mm Two-Color LED Module

Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150

Reference: RBD-2077

3mm Two-Color LED Module

Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:3mm Wavelength:571nm + 644nm Beam Angle:150

Reference: RBD-2078

Vibration Switch Module

No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA

Reference: RBD-0840

Veroboard Dot Type

48 reviews

Dimension: 14.5×6 cm Copper Thickness 1-4 OZ Board Thickness 1.1 mm Board color: Brown

Reference: RBD-2086

Momentary Tactile Push Button Module DC 5V Switch

1 review

Operating Voltage: 5V Contact Resistance : 50mΩ max (initial) Electrically Life:100,000 cycles Environment temperature: -25°C to +105°C Operating Force: 180/230(±20gf) Seal temperature:250ºC-280ºC I/O pins: 3 pins

Reference: RBD-2093

Photosensitive Resistor LDR Sensor Module

This is a High-quality photosensitive sensor module/light module detects the photosensitive resistor for Arduino Resistance of the photoresistor is typically less than 80 Ohms (in full light) Dark resistance is typically greater than 20 Meg Ohms (in full darkness)

Reference: RBD-0919

TP4056 Lithium Battery Charger Module With Protection Dual Functions

57 reviews

Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.

Reference: RBD-2102

DIP 3 Color RGB LED Module

4 reviews

RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing

Reference: RBD-1044

1.5W 8ohm Mini Speaker DIY

11 reviews

Rated Power 1W Impedance 8ohm Small

Reference: RBD-2150

Anti-Reverse Diode Constant Current Module 60V 10A For Backflow Protection

Type: Voltage Regulator Operating Temperature: -40-+85 Supply Voltage: 60v Dissipation Power: 10A Package: SMD

Reference: RBD-1363

Veroboard Line Type

18 reviews

Dimension: 14.5×6 cm Copper Thickness 1-4 OZ Board Thickness 1.1 mm Board color: Brown

Reference: RBD-2244

LilyPad Slide Switch

Wearable e-textile technology.  Designed with large sew tabs Slide Switch

Reference: RBD-2301

Active Buzzer Module

2 reviews

An Active Buzzer Alarm Module for Arduino is an audio signaling device, which may be mechanical, electromechanical, or piezoelectric.it is a 3.3V-5V DC Electronic Part Active Buzzer Module. This active buzzer rings out as long as it is electrified. Compared with a passive buzzer, it is a bit expensive but easier to control. Typical uses of buzzers include...

Reference: RBD-2323

NeoPixel 5050 WS2812B 1Bit RGB LED with Integrated Driver

The WS2812B RGB LED Module is a small module with BIG color.  The module has a special LED on board that contains three separate LEDs – red, green, and blue – as well as a smart control IC that can individually drive each LED.  Each color has 256 intensity levels which allows the module to produce 24-bit color, or more than 16 million colors.  Each module...

Reference: RBD-1658

Double Sided FR-4 PCB Prototype Board 4x6cm

8 reviews

Dimension: 4×6 CM Quantity: 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 6 gm PCB color: Green

Reference: RBD-2428

Potentiometer with Built In Knob - 10K ohm

Sorry - we thought that was clever.  And while it wasn't really, this potentiometer definitely is! We've seen these in miniature synthesizers. They're bigger than a trim-pot but smaller than a chunky potentiometer. Best of all no knob required! These have a knurled plastic grip with a white stripe marking. Use it as-is, for a low-cost adjustment Comes as...

Reference: RBD-2813

1.5W 8ohm Micro Speaker DIY

Compact Size: Fits perfectly into small spaces for creative DIY projects. Clear Sound: Delivers surprisingly good audio quality for its size. 8Ω Impedance: Compatible with most DIY amplifier boards. Easy Integration: Ideal for embedding into electronics or crafts.