Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1670
The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA
Reference: RBD-1751
Detection Gas: H2, Alcohol, CO, VOC Detection Range: 10~500ppmH2 5~500ppm Alcohol 10~500ppm CO Air Quality Sensor Module
Reference: RBD-2294
JQ6500 MP3 Voice sound module can play stereo MP3 files or standard mono audio files. The module has two different modes to operate in; serial communication mode (connecting to a microcontroller) or AD button control mode (module can be controlled with switches).
Reference: RBD-2331
This is a rotary potentiometer module consisting of 8 adjustable potentiometers and the communication method is IIC interface. The module mainly uses 10K adjustable resistors. By rotating the potentiometer to change the size of the resistance value, then build a circuit to convert the change of resistance value to voltage change, read the output value...
Reference: RBD-2459
Converts 5 – 30V down to a 0.8 – 29V output with adjustable current limit
Reference: RBD-2475
5 counters with 2 end caps are bundled togeatherbezel size 1.85" x 0.94" (for 5 counters with 2 end caps) mounting hole size 1.72" x 0.875" (for 5 counters with 2 end caps) total depth (from front of button to the edge of the PCB) 1.6" single counter width 0.32"
Reference: RBD-2489
Wiznet Compact W5500 Network Module - 10/100 Base T WIZ850io is a compact size network module that includes a W5500 (TCP/IP hardwired chip and PHY embedded), a transformer and RJ45. It can be used as a component and no effort is required to interface W5500 and Transformer. The WIZ850io is an ideal option for users who want to develop their Internet...
Reference: RBD-2672
MCP3008 is one of the famous Analog to Digital converter IC. This chip will add 8 channels of 10-bit analog input to your microcontroller or microcomputer project. It's super easy to use, and uses SPI so only 4 pins are required. We chose this chip as a great accompaniment to the Raspberry Pi computer, because its fun to have analog inputs but the Pi does...
Reference: RBD-2676
Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...
Reference: RBD-2720
Chip type: W5500. Supports both 3.3V & 5V. Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE. 10BaseT/100BaseTX Ethernet PHY embedded. Supports automatic response (full duplex/half duplex mode). Internal 32Kbytes Memory for Tx/Rx Buffers.
Reference: RBD-2761
ICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/Sine Wave Generator, Module Working voltage: 12V ~ 15V Output: Triangular wave, Square wave and sine wave. Frequency range: 10HZ ~ 450kHz Low distortion sine wave: 1% Duty cycle range: 2% to 98% Low temperature drift: 50ppm / ℃ Triangular wave output...
Reference: RBD-2341
Operating Voltage: 2.7V ~ 5.5V Power Down Feature Stable Temperature Coefficient Can be directly interfaced with a Microcontroller Compatible with Arduino as well as Raspberry Pi.
Reference: RBD-2351
HLK-LD2410C is a high-sensitivity 24GHz human presence status sensing module developed by Hi-Link Electronics. Its working principle is to use FMCW frequency-modulated continuous wave, to detect human targets in the set space, combined with radar signal processing, accurate human body induction algorithm, to achieve high sensitive human presence status...
Reference: RBD-2361
Working voltage: 3V-5V (MAN SV) Static output voltage: VCCi2 Working current: 135m2A (MAX) Small in size, with easy mounting capability. Monolithic Hall IC for high reliability
Reference: RBD-2452
This Pulse Sensor is a heart rate sensor designed for Arduino microcontrollers. Development professionals use. The Pulse Sensor Kit brings you all the experience you need, a complete package. The kit includes: A 24inch 3p DuPont line, A soft Velcro Finger Strap, A sensor size sensor ear clip, 4 Velcro dots, and 9 transparent protective dot Pulse Sensor is...
Reference: RBD-2762
The GY-362 ADXL362 Sensor Module is a high-precision accelerometer module designed for a wide range of motion sensing applications. Powered by Analog Devices' ADXL362, this module offers ultra-low power consumption, exceptional accuracy, and versatile functionality.
Reference: RBD-2783
The GY-51 LSM303DLH chip has an accelerometer, magnetometer, A / D converters and signal conditioning circuit integrated. Still, the communication to the processor is done through the I2C bus. Thus only one chip is required to achieve a six-axis data detection and output. The LSM303DLH requires very little peripheral devices.
Reference: RBD-2806
K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃
Reference: RBD-2845
Waterproof analogue sensor with the high temperature working in the range from -200°C to 420°C. The output is resistance dependent on temperature. Probe length is 200 mm.
Reference: RBD-2852
Shape: Circular. Sensing Area diameter (mm): 18.3 Min Force: 20 gm. Max Force: 6Kg. Length (mm): 60. Weight (gm): 2.