Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1856
Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...
Reference: RBD-2694
Incredibly thin (just over 4mm) 4cm speaker for adding sound to projects with severe space constraints. 8Ω impedance and 0.5W power handling for compatibility with low-power audio circuits. Ideal for applications like portable devices, greeting cards, or space-limited enclosures.
Reference: RBD-1594
29mm diameter 10 LED Dimmable 50-degree viewing angle
Reference: RBD-1595
50mm diameter 12 LED Dimmable 50-degree viewing angle
Reference: RBD-1795
Diameter 4mm and Length 20 (M4 x 20) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1799
Diameter 5mm and Length 10 (M5 x 10) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-2424
5.08mm pitch. Pin header: Tin plated brass. Contacts: Nickel plated brass. Strong, compact, lightweight. Heat resistant.
Reference: RBD-2621
Diameter 5mm and Length 8 (M5 x 8) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1231
Male to female threaded for secure PCB and machine board mounting Hex head design allows for easy tightening with a wrench Ideal for creating space between circuit boards Brass construction offers durability and corrosion resistance Available in 30mm length with M3 threads
Reference: RBD-2634
Female to female threaded for secure PCB and machine board mounting Hex head design allows for easy tightening with a wrench Ideal for creating space between circuit boards Brass construction offers durability and corrosion resistance Available in 50mm length with M3 threads
Reference: RBD-1512
LDR 10 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.
Reference: RBD-2076
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150
Reference: RBD-2077
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:3mm Wavelength:571nm + 644nm Beam Angle:150
Reference: RBD-2078
No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA
Reference: RBD-2102
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing
Reference: RBD-2125
Phototransistor output No contact surface sensing Miniature package
Reference: RBD-2792
This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor...