Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0103
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications. Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch...
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-1324
Operating voltage: 2.5V-5.5V Maximum output power: 3W x 2 PCB size is about: length 30mm width 22mm overall height after installed is about 16mm Built with switch Potentiometer, can adjust the volume & control power switch freely! Flexible assembly usage.
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-1856
Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-2695
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-2691
Compact 15mm speaker for integrating sound into space-constrained projects. 2kHz frequency range suitable for basic audio applications. Through-hole mounting for easy integration with circuit boards. Handles up to 0.5W of power for moderate sound output.
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-2692
Breadboard-Friendly PCB Mount Mini Speaker - 8 Ohm 0.2W 1.1" (~30mm) diameter speaker with 8 Ohm impedance Perfect for breadboard-based audio projects Durable plastic casing, lightweight design Power handling: Nominal 0.1 Watts, Maximum 0.2 Watts
Reference: RBD-0697
Driver Chip: CH340G Supports all basic windows versions. The adapter plate integrated 1000μF solid capacitors to ensure the current supply The power supply will not be a problem to make WIFI module crashes unresponsive. Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall. Working voltage: 4.5V – 5.5V (Onboard...
Reference: RBD-2693
Compact 5cm speaker for integrating audio into various projects like radios, amplifiers, and robots. 8Ω impedance and 0.5W power handling for compatibility with common audio circuits. Lightweight and space-saving design for versatile integration.
Reference: RBD-2694
Incredibly thin (just over 4mm) 4cm speaker for adding sound to projects with severe space constraints. 8Ω impedance and 0.5W power handling for compatibility with low-power audio circuits. Ideal for applications like portable devices, greeting cards, or space-limited enclosures.
Reference: RBD-2724
The MAX4466 Electret Microphone Module is a convenient and sensitive audio sensor solution designed for capturing sound waves and converting them into electrical signals. This module incorporates the MAX4466 electret condenser microphone and an integrated amplifier circuit, making it well-suited for applications requiring clear and amplified audio capture.
Reference: RBD-0733
Connects Devices & Antennas: Ideal for WiFi, Bluetooth, and nRF devices to 2.4GHz antennas. Enhanced Usability: 150mm length (compared to standard 100mm) provides more flexibility for enclosure integration. Reliable Signal: 50Ω impedance ensures efficient signal transmission. Durable Construction: Built with high-quality materials for long-lasting...
Reference: RBD-2747
This is a small 12mm round speaker that operates around the audible 2kHz range. You can use these speakers to create simple music or user interfaces. This is not a true piezoelectric speaker but behaves similarly. Instead of a piezoelectric crystal that vibrates with an electric current, this tiny speaker uses an electromagnet to drive a thin metal sheet....
Reference: RBD-1641
Product: GSM Antenna Color: Black SMA male straight 5cm 900-1800MHz radio antenna. Frequency: 900MHz – 1800MHz Maximum Power: 50W Length: 5cm/1.97 inch
Reference: RBD-2103
Remote control distance: more than 8 meters Crystal: the oscillation frequency of 455 IR carrier frequency: 38KHz Output form: Digital Power Supply: CR2032 Battery Pointing Angle: up to 60º Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click
Reference: RBD-2234
¼ wave rubber duck antenna 860-960MHz communication center frequency of 915MHz RP-SMA connector Gain is 2dBi with an overall length of 110mm
Reference: RBD-2456
Breakout adapter includes a built-in 3.3V regulator and easy header hookup.
Reference: RBD-0896
Frequency Range: 890-960/1710-1880MHz Bandwidth: 70/170 MHz Gain: 1.5dBi VSWR ≤1.5 Polarization: Vertical Max Power: 50 W Nominal Impedance: 50 Ω