Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1771
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1781
1. Micro USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 16 x 14 mm .
Reference: RBD-1785
1. USB3.0 Type A Female ( 9pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 28 x 25 mm .
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-1892
Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-1957
Input Voltage: 12V Connector: 5.5mm DC Jack Output power on/off switch Two-row multiple pin outputs, easy to use and connect Outputs 3.3V DC at 800mA maximum current Outputs 5.0V DC at 800mA maximum current Outputs 12V DC (the 12V output is directly connected to the input, i.e. with 12VDC input, this output will be 12VDC; with 9VDC input, this output will...
Reference: RBD-2457
Regulates 4.5 – 40V input to a 1.25 – 37V output @ up to 1.5A
Reference: RBD-2817
Ultra-Compact Size: 200 mm (approximately 8 inches) in length, perfect for connecting devices in confined spaces. Direct U.FL Connection: Eliminates the need for bulky adapters, ideal for connecting U.FL equipped devices. Exceptional Flexibility: 1.25mm diameter cable offers easy maneuvering for intricate installations. 50Ω Impedance: Ensures efficient...
Reference: RBD-2818
Ideal for transmitting and receiving radio waves at 433MHz frequency. Spring form factor saves space and simplifies integration. Gold-plated finish offers lasting performance (other plating options available). Solder-type connection for efficient integration.
Reference: RBD-2653
2.8V-5.5V to ±12V DC Conversion Step Up Power Supply Module is straightforward. There is a 2.8 to 5.5 V DC input and the module outputs +12 V and -12 V DC dual power supply voltage with a current rating of a maximum 30 mA. Off course the current output is low but sometimes it suits in many situations where one is looking forward for a small boost...
Reference: RBD-0621
Connects Your Arduino Nano: Provides essential connection between your Arduino Nano and a computer for programming and power. Standard Compatibility: Features USB Type-A and Mini-B connectors for universal computer connectivity. Reliable Performance: Solid workmanship and high-quality materials ensure dependable data transfer. Flexible Design: 1-meter...
Reference: RBD-2726
2A 5V Charge Discharge Integrated Module 3.7V 4.2V for 18650 Lithium Battery Charging Boost Mobile Power Supply Charge and Discharge Protection Converter Protection PCB Board Module