Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-1363
Dimension: 14.5×6 cm Copper Thickness 1-4 OZ Board Thickness 1.1 mm Board color: Brown
Reference: RBD-1862
44mm diameter 30 LED Dimmable 50-degree viewing angle
Reference: RBD-2317
The is a 4 way navigation switch (north, south, east, west) with a center push. Think of it as a mini joystick. Whilst the pins don’t align perfectly to a 2.54mm grid, it can be made to fit into a breadboard or perfboard by bending the pins.
Reference: RBD-2428
Sorry - we thought that was clever. And while it wasn't really, this potentiometer definitely is! We've seen these in miniature synthesizers. They're bigger than a trim-pot but smaller than a chunky potentiometer. Best of all no knob required! These have a knurled plastic grip with a white stripe marking. Use it as-is, for a low-cost adjustment Comes as...
Reference: RBD-2476
These nice switches are perfect for use with breadboard and perfboard projects. They have 0.1" spacing and snap in nicely into a solderless breadboard. They're easy to switch no matter what size fingers you have, but not so easy that they'll get flipped by accident. Work great as on/off switches or selector switches, the middle pin is connected to either...
Reference: RBD-2564
This MOSFET module with optoisolation uses the LR7843 N-Channel logic compatible MOSFET with ultra low Rds(on) for moderate to higher current low-side switching applications of up to 15A continuous. N-Channel logic compatible MOSFET with optoisolation and ultra low 3.3mΩ Rds(on)
Reference: RBD-2748
A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually, the battery runs down and goes below 3.3V, so the voltage to the ESP8266 core is too low, and could cause a lockup or corrupted data....
Reference: RBD-2749
Transistors are powerful little electronic switches, and when little NPN transistors aren't powerful enough for your project, use these beefy TIP120 Darlington transistors. Great for whenever you need to control medium to high-power electronics such as motors, solenoids, or 1W+ LEDs. We find them so handy, they come in a pack of 3! Each transistor is a...
Reference: RBD-2750
This is a common MOSFET with very low on-resistance and a control voltage (aka gate voltage) that is compatible with any 3-5V microcontroller or mechanical switch. This allows you to control high-power devices with very low-power control mechanisms.
Reference: RBD-2751
Ah the esteemed LD1117, who amongst us has not used this popular low drop voltage regulator? This big chunky regulator will help you get your 4-15V battery or wall adapter down to a nice clean 3.3V with 1% regulation. Perfect for just about all electronics! This is the TO-220 version, with up to 800mA current capability, and has internal current limiting...
Reference: RBD-2755
When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220s, but because of the very low Rds(on) of down to 70 mOhms (depending on the Vgs - check the...