Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

14 reviews

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-1101

5V Micro USB Tiny AVR ISP USBTinyISP Programmer Module For Arduino IDE Bootloader ISP Microcontroller

1 review

Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB

Reference: RBD-1102

ST LINK Stlink ST-Link V2 Mini STM8 STM32 Simulator Download Programmer

4 reviews

PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...

Reference: RBD-1212

USB to Serial RS232 DB9 Converter Cable

5 reviews

Single crystal 12M Tablet 340 USB port to serial port communication. USB1.1/2.0 compliant solution. Built-in 128 byte TX/512 byte RX buffer. Supports auto-Handshake Protocol. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol. Design of electromagnetic interference. Data Exchange application. CH340 USB...

Reference: RBD-0662

EasyDriver Shield Stepper Motor Driver V44 A3967 For Arduino

Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

9 reviews

CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1

Reference: RBD-2198

CH341 USB Programmer

Model: CH341 Series Main Chip: CH341B Dimensions in mm (LxWxH): 85 x 28 x 12 Weight (gm): 20 8-bit parallel in EPP or MEM mode

Reference: RBD-2412

USB ASP AVR Programming Device for ATMEL Processors Arduino

1 review

Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader

Reference: RBD-2413

FTDI Basic Breakout USBTTL 6PIN 5V Module Fio/Pro/RGB/Lilypad Programmer

Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...

Reference: RBD-1762

Mini BD243 Bubble 9-12V Tesla Coil Electronics Wireless PCB Module

4 reviews

Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm):  3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.

Reference: RBD-2416

WEMOS CH340G Breakout 5V 3.3V USB to Serial Module

5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver

Reference: RBD-2427

USB Type-C Cable 1meter for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-1809

Digispark Pro - ATtiny167 with Micro USB

Digispark Pro  ATtiny167  Micro USB 16MHz

Reference: RBD-2463

Programmer Testing IC Test Clip Black SOIC8/SOP8 Flash Chip IC Test Clamp

The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...

Reference: RBD-2389

L298N Dual H-Bridge Motor Driver Module

This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.

Reference: RBD-2676

PWM Signal Generator Stepper Motor Speed Controller Driver Board

Suitable for use with a wide range of stepper motors and drivers. Can be integrated into a simple control platform with a stepper motor and DC power supply. Offers three selectable low-frequency signal options: high (5.4k-160kHz), middle (540-16.6kHz), and low (80-2.4kHz), adjustable via jumper settings. Capable of producing both pulse and PWM signals,...

Reference: RBD-2113

FR4 CCL Copper Clad Plate Laminate Single Side PCB Glass Fiber

Single side PCB. Reinforced with glass fiber laminate on the core. 215 x 330 x 1.4 mm. Ideal for prototyping. Color: Ash, White Smooth Machine Cut

Reference: RBD-1663

Brand: RoboticsBD

Breadboard Bundle Pack

3 reviews

Distribution strip, Tie-point 200 Terminal Strip, Tie-point 630 Completely reusable Breadboard Brand new & high quality Breadboard power supply module, compatible with 5 V, 3.3 V 140pcs Solderless Breadboard Jumper Cable Lead Kit Hard Wire with Angled shape

Reference: RBD-2652

Wemos D1 Mini NodeMCU

Firstly, In terms of pins, the D1 Mini and NodeMCU V3 development boards are quite similar. They both break out all ESP8266 ESP-12E/F pins. The NodeMCU V3 board has additional 3V3 and GND pins. Hence,  it is more suitable for various connections to devices with an additional button for the flash. Furthermore, you can flash either board with NodeMCU...

Reference: RBD-2679

STM32F103C8T6 ARM STM32 Minimum System Development Board Module

STM32F103C8T6 ARM Development Board Module with Type-C Interface and Enhanced Memory Enhance your embedded system projects with the STM32F103C8T6 ARM development board module. Featuring a Type-C interface for easy connectivity, this module offers seamless one-click download capability. With an upgraded BOOT switch, you can easily perform upgrades without...

Reference: RBD-2689

FR4 Copper Clad Plate Laminate Single Side PCB - 0.8 mm thickness

Single side PCB. Reinforced with glass fiber laminate on the core. 330 x 200 x 0.8 mm. Ideal for prototyping. Color: Copper, White Smooth Machine Cut

Reference: RBD-2690

FR4 Copper Clad Plate Laminate Single Side PCB - 1.4 mm thickness

Single side PCB. Reinforced with glass fiber laminate on the core. 330 x 200 x 1.4 mm. Ideal for prototyping. Color: Copper, White Smooth Machine Cut

Reference: RBD-2831

Raspberry Pi Pico China

Introducing a compatible Raspberry Pi Pico Clone, Made in China. Equipped with the authentic Raspberry Pi RP2040 microcontroller chip, this Pico offers comparable performance at a competitive price point. However, it's essential to note that while the microcontroller chip is genuine, the PCB itself is not manufactured by Raspberry Pi but rather in China....