How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-1102
PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...
Reference: RBD-1103
Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc....
Reference: RBD-1104
Isp interface: 6 PIN Isp interface: 10 PIN Power supply options: USB power Power supply options: external power supply (remove jumper cap)
Reference: RBD-0557
Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0430
Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0572
Operating Power: 60mW/15fpsVGAYUV. Sleeping Mode: <20 uA. Lens Size: 1/6″. Max. Frame Rate: 30fps VGA. Sensitivity: 1.3V / (Lux-sec). dynamic range: 52 dB. Electronic Exposure: 1 to 510 row.
Reference: RBD-0666
Crystal: the oscillation frequency of 455. Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000. Photo-detector and preamplifier in one package. Internal filter for PCM frequency. RoboticsBD Improved shielding against EMI. Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
Reference: RBD-0797
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...
Reference: RBD-0812
Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.
Reference: RBD-0922
Dimensions: 91 x 21 x 30 mm(LxWxH) Weight: 18 gm. Voltage: 3.3V or 5V. Port: Analog. Resistance: 10K. Appn: Raspberry-Pi projects. DIY projects., Arduino projects.
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and...
Reference: RBD-1066
Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.The Mini Metal Detector Module arrives disassembled, requiring assembly using a soldering iron and soldering accessories. Moderate knowledge of soldering and...
Reference: RBD-1204
Distance measuring range: 100 cm to 550 cm Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms
Reference: RBD-1405
Working voltage: 5.00V DC Working current: 40mA (MAX) Response time: <500ms Insulation resistance: 100MΩ (Min) Analogue output: 0~4.5V; Digital output: high/low-level signal (the corresponding threshold can be selected by adjusting the potentiometer) Operating temperature: -20℃~90℃
Reference: RBD-1644
940nm laser classified as class 1 under operation condition by IEC 60825-1:2014-3rd edition Small ceramic package(20×13.2×2.0mm) Long range absolute range measurement up to 1.8m within 5% accuracy at indoor
Reference: RBD-1645
Voltage operation: 2.7V-5V Measuring distance: 4 to 50 cm Output: Digital (I/C) / Analog Output Sensor: Infrared LED and CMOS image sensor
Reference: RBD-1648
FPC1020A is a secondary development module for fingerprint recognition designed for SCM. Fingerprint identification capacity: 150 fingerprints, identification time is less than 1 second, can be customized large capacity Capacitive surface array semiconductor fingerprint sensor Support finger 360 rotation recognition Supported Operating Systems: Windows
Reference: RBD-1737
Fastest fingerprint identification in the world, Support multi fingerprint Instant match.
Reference: RBD-1766
Supports 5V/3.3V input Onboard RT9161 faster load the appropriate speed Ideal for noisy power environment Application: DIY project.
Reference: RBD-2144
Automatic induction: to enter the sensing range Ultra-small size. Repeatable trigger Wide operating voltage range Micropower: quiescent current <50 Output high signal: easy docking and all kinds of circuits.
Reference: RBD-2217
Based on the semiconductor LM35 temperature sensor Can be used to detect ambient air temperature Calibrated directly in °Celsius (Centigrade) Linear + 10 mV/°C Scale Factor 0.5°C Ensure accuracy (at +25°C) Low power consumption, less than 60uA Low output impedance, 1mA current through only 0.1Ω With screw holes for easy installation and fixed. Aperture...
Reference: RBD-2384
Module for measuring infrared temperature Uses the GY-MCU90640 MLX90640 BAA 32*24 dot matrix sensor Field of view angle of 110*75 degrees Ambient temperature range of -40 to 85 degrees Target temperature range of -40 to 300 degrees Serial output frequency supports up to 16HZ baud rate 460800
Reference: RBD-2385
Module for measuring infrared temperature Uses the GY-MCU90640 MLX90640 BAA 32*24 dot matrix sensor Field of view angle of 55*34 degrees Ambient temperature range of -40 to 85 degrees Target temperature range of -40 to 300 degrees Serial output frequency supports up to 16HZ baud rate 460800
Reference: RBD-2639
Connect components on breadboards and PCBs easily. 20 pre-crimped jumper wires for versatile use. 20cm length for convenient connections. Male-to-male connector design for simple use. Colorful for easy identification and organization.
Reference: RBD-2640
Connect components on breadboards and PCBs with ease. 20 pre-crimped jumper wires for versatile use. 20cm length for convenient connections. Male-to-female connector design for flexible connections. Colorful for easy identification and organization.
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0133
830 Solder-less Points Ideal for Experimenting With Circuit Design In Labs Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components Colored coordinates for easy components placement. Accept a variety of wire sizes 20-29 AWG
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: 0245
Choose your desire Resistor value from below:
