Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0169
Flex length: 5.6 cm. Total Length: 2.2″ (7 cm). Life Cycle : >1 million. Height : 0.43mm (0.017″), Flat Resistance: 10K Ohms ±30%. Power Rating: 0.5 Watts.
Reference: RBD-1250
DC 12V 195 RPM 37GB-545 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-1390
Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.
Reference: RBD-2067
7-70V 30A PWM DC Motor Speed Controller Switch Wide voltage input range: 7-70V Maximum output current: 30A Speed control knob with switch function Adjustable potentiometer with flexible cable (15cm length) Includes a 30A fuse for motor interface protection Input power must be 1.5 times greater than the motor's rated power
Reference: RBD-0188
Logical light indication: a small light indicate CHO electrical level. Input feature: 5PF,100K Ohm. USB power supply; USB logic analyzer for monitoring, analyzing and debugging digital circuits 8-Channels USB logic analyzer with a 24Mhz sampling frequency Can analyze UART, IIC, and SPI, etc automatically Great for MCU, ARM system and FPGA development...
Reference: RBD-0189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-0297
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0208
"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."
Reference: RBD-0936
High-Quality Pump Operating Voltage: 12VDC Flow Rate: 1100GPH Outlet Diameter 19mm
Reference: RBD-0394
They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD
Reference: RBD-1357
DC 12V 300 RPM 37GB-555 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-1682
DC 12V 100 RPM 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-1849
High torque and low noise. Great replacement for the rusty or damaged DC gear motor on the machine. Ball bearing, with the cooling fan. Used in electric tool motors, power is very large, you can make a small spindle motor, and is also suitable for DIY aspects. Used for the electronic game machines, electronic toys, car toys, robots,
Reference: RBD-1868
Watering configuration: much the same, additional sprinklers and timers are required 12V DC reflux diaphragm pump 550, the price is the price of a pump, without other accessories Maximum pressure: 0.8MP. Voltage: 12V, current: at least 2A, measured 1A is not able to bring Suction: 3 meters or so, preferably 2 meters (no problem if the vertical height is...
Reference: RBD-1960
Small size, light weight. Embedded in the work front panel Mounted on the carriage.
Reference: RBD-2250
JGY-370 DC 12V 160RPM Self-locking Reduction Worm Gear Motor
Reference: RBD-2277
DC 12V 400 RPM 37GB-555 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-2524
DC 12V 200 RPM 37GB-555 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-1015
Power Supply: 90V~250V AC(50/60Hz) Max. Current: 10A/gang Max. Power:2200W/gang, 2200W/Total Wireless Standard: 802.11 b/g/n Security Mechanism: WPA-PSK/WPA2-PSK Enclosure Material: Fire-retardant ABS V0
Reference: RBD-2803
This is NEMA17 stepper motor commonly used in 3D printers, CNC machines, and linear gantry systems.
Reference: RBD-2897
DC 12V 500 RPM 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-3006
It is a simple 2 phases hybrid stepper motor. It features 3.5kg high torque output. It is applied in most CNC machine or 3D printer such as makerbot and ultimaker. If you want to make your own CNC or 3D printer, this motor is the most suitable one. Usually, a CNC machine requires 3 motors and a 3D Printer requires 4.
Reference: RBD-1685
5050 12V RGB Led Strip light 4pin LED Headers For PC, Computer Case RGB Strip Mainboard Control Panel RGB-Header (+12V,G,R,B) 5x0.5m Waterproof
Reference: RBD-0276
The INA125 is a low-power, high-accuracy instrumentation amplifier with a precision voltage reference. It provides complete bridge excitation and precision differential-input amplification on a single integrated circuit. A single external resistor sets any gain from 4 to 10,000. The INA125 is laser-trimmed for low offset voltage (250µV), low offset drift...