Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0494
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: STD-120200
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0696
Voltage : Input through (USB) DC 5V Output via (DC Round Pin) : DC 12V Color: BLACK Input / Output Current: Maximum Input 0.6 Easier for installation save time and money Easy to use.
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-0282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Reference: RBD-1309
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 5V 3A. Load regulation (%): ±5. Input Plug: 2-Pin EU type. Output Plug: Micro USB Plug. Compatible with: Raspberry Pi B+, 2, 2B, 2B+,3 ,3B+, Zero, Zero W. It has a switch so you can easily power off the device without having to unplug it right from the socket.
Reference: RBD-1559
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1560
Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-1564
High voltage resistant terminal. Support solar charging. Support undervoltage protection. Support short circuit protection.
Reference: RBD-1673
Supports Qualcomm Quick Charge 3.0 fast charging protocol Has both "USB type C" and "Micro USB" port for charging power bank battery Power bank battery can be fast-charged (up to 15 watts) with QC 3.0 supported fast chargers Two "USB A" ports with maximum 18-watt power delivery from the power bank Power bank battery level indicator LEDs and power on/off...
Reference: RBD-1690
ON/OFF switch button on the power adapter. Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-1697
Brand: DFRobot
Takes a 6-12V input voltage. Outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. Powered from 6-12 DC2.1 power jack or from USB power. The maximum current it can provide is 500mA.
Reference: RBD-1702
Very convenient for use. 5V 1.5A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-1764
High Power DC-DC Step Down Module Input Voltage: 5-40V DC Output Voltage: 1.2-36V DC Efficiency: 95% Maximum Power: 200W
Reference: RBD-1853
Suitable for Arduino, DIY & Hobby Kits, and 5V Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-1874
Suitable for DIY & Hobby Kits, Routers, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved.
Reference: RBD-1879
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: NBSB24120200VU Brand: Motorola
Reference: RBD-1915
Input voltage range : 3-34V DC Output voltage range : 4-35v DC adjustable Output current:3A Voltmeter range:0 to 40V,error +-0.1v Multiple output regulator. One button to switch input and output voltage display. Power-down memory function. Press the button for 3 seconds can turn OFF/ON the LED display.
Reference: RBD-2355
The Type-C 3A High Power 9V 18650 Lithium Battery Boost Charging Module is designed for non-power failure applications where seamless power supply switching is required. It allows for external power supply usage when available and automatically switches to battery power during power outages. When utilizing the USB interface for power supply, it is...
Reference: RBD-2356
The Type-C 3A High Power 12V 18650 Lithium Battery Boost Charging Module is designed for non-power failure applications where seamless power supply switching is required. It allows for external power supply usage when available and automatically switches to battery power during power outages. When utilizing the USB interface for power supply, it is...
Reference: RBD-2370
Module Properties: non-isolated Buck-Boost constant current, constant voltage module (CC-CV) charging module Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Solar Panel, Wind generator voltage regulator, Car Power Supply
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink
Reference: RBD-2458
The XH-M404 Adjustable DC-DC Step-Down Module can can step-down the input voltage to a range of 1.25 – 36V at up to 8A.
Reference: RBD-2459
Converts 5 – 30V down to a 0.8 – 29V output with adjustable current limit
Reference: RBD-2460
LTC1871 DC-DC 3-35V To 3.5-35V Booster Step Up Module Converter Regulated Power 100W Buck-Boost Adjustable Supply LED VoltMeter
Reference: RBD-2466
This XL4015-based voltage converter is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module with Constant Voltage and Constant Current control, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation.
Reference: RBD-0873
Passive PoE injector for outdoor radios, switches, and other network equipment Compatible with network devices that allow 48 Vdc passive PoE power Transmits power and data to remote devices up to 100 meters away
Reference: RBD-2656
TPS63020 Automatic Buck-boost Step up Down Power Supply Module 5V Lithium Battery Low Ripple Voltage Converter TPS63020 is a high-efficiency small buck-boost power supply module. The input voltage ranges from 1.8V to 5.5V, the output current can be as high as 3A, and the efficiency is as high as 96%. It can automatically switch between buck and boost...