Reference: RBD-0276

INA125P IC

1 review

LOW QUIESCENT CURRENT: 460µA PRECISION VOLTAGE REFERENCE: 1.24V, 2.5V, 5V or 10V SLEEP MODE LOW OFFSET VOLTAGE: 250µV max LOW OFFSET DRIFT: 2µV/°C max

Reference: RBD-0344

Weighing Sensor 24 Bit Load Cell Amplifier HX711

13 reviews

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD

Reference: RBD-1103

ALTERA Mini USB Blaster Cable for CPLD FPGA NIOS JTAG Programmer

2 reviews

Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc....

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-2281

13.56MHz RFID IC Key Tag

1 review

Material: ABS Dimension(LxWxH): 43.7×30.5×5.3mm Response Frequency: 13.56MHz Chip type: FM1108 Fudan Chip Memory capacity: 8 kbit Designed for the RFID 13.56MHz duplicator. can copy all the ID card, such as Access Card, District Card, Parking etc.

Reference: RBD-1700

Brand: Waveshare

ST-LINK V2 Mini- STM Programmers & Debuggers

Mini ST-LINK/V2  Small single board Extreme low cost solution  In-circuit debugger/programmer  STM8 STM32.

Reference: RBD-2142

CH340C WIFI Module Adapter Download Debug for ESP8266 ESP-01/01S

2 reviews

Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.

Reference: RBD-1344

Current to Voltage Transmitter Module

Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V

Reference: RBD-1679

Solid Round Slip Ring 6 Wire

Slip Ring 6 Wire (1.5A) max 240V

Reference: RBD-1816

TTL to RS485 Converter 3.3V/5V Hardware Automatic Control Converter Module

Anti-Interference Ability Baud rate: 110 ~ 256000bps Operating Voltage: 3v  to  30VDC Compatible With Both 3V and 5V logic

Reference: RBD-1834

PT100 to 0-5V Converter PCB-mounted PT100 to 0-10V Conversion Module RTD PT100 to Voltage Signal Conditioner

PT100 to 0-5V Converter Voltage Signal Conditioner PCB-mounted

Reference: RBD-2056

PT-100 RTD Temperature Sensor 3 Wire 50cm

Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s