Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0422
Dimensions: 210 x 17 mm(LxW) Weight: 8 gm. Fit for Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL (GT-511C1R) Wire Sleeve material: Silicon. RoboticsBD
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-2234
¼ wave rubber duck antenna 860-960MHz communication center frequency of 915MHz RP-SMA connector Gain is 2dBi with an overall length of 110mm
Reference: RBD-1158
Width: 10 mm Length: About 33m. Type: Polyimide Tape. Heat Resistance: 200℃. Thickness Tolerance: ±10% . One-side Self-adhesive.
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-1636
4-PIN Toggle Switch ON-OFF Two Position Switch 15A 250V VE147 P
Reference: RBD-0983
Capacity (mAh): 960-2000 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life SMALL SUN
Reference: RBD-1371
Input: AC 100-240V/ 47-63HZ Output: DC 3.7V/ 500mA Termination voltage: 4.2V+-1%
Reference: RBD-2644
Pixel chain - 25x LED 5mm Red 25 bright LEDs in Red color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2645
Pixel chain - 25x LED 5mm Blue 25 bright LEDs in blue color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2646
Pixel chain - 25x LED 5mm Green 25 bright LEDs in Green color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2647
Pixel chain - 25x LED 5mm Yellow 25 bright LEDs in yellow color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-0945
Length: 1.5m Weight: 82 gm. Color: Steel Black Supports all HDTV devices including 1.4 Supports resolution up to 1080P Supports 3D and Blu-ray Disc
Reference: RBD-1623
Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-0827
High-quality ABS construction Available in both red/white and black/grey Removable side panels and lid for easy access to GPIO, camera and display connectors Light pipes for power and activity LEDs Extraordinarily handsome. RoboticsBD
Reference: RBD-0109
Support HD resolution, super clear picture, fast transmission speed The maximum signal range up to 1920 X 1200, 1080p; Video input signal: 5Volts p-p(TTL) ; Support VGA video bandwidth: 10 bit, 162MHz Video amplifier bandwidth: 162MHz Support resolution up to 1920 X 1200, reduce blank signal during transmit. No external power supply, plug, and play.
Reference: RBD-1907
Doublepow AA 1200MAH Battery 2pcs/Set 1.2V Ni-MH Rechargeable Battery
Reference: RBD-2816
Connects Devices: Ideal for connecting components with SMA connectors for signal transmission. Durable Design: Threaded connectors and 50Ω impedance ensure reliable signal transfer. Wide Range Use: Suitable for various applications up to 17 GHz frequency. Compact & Flexible: 250mm length offers easy integration in most setups.
Reference: RBD-2408
Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the dozen for making programming and testing jigs but they're handy also if say you want to JTAG program a board that you can't solder headers to.Total Length: 17.5mmTop Length Length: 15mmPin Spacing 2.54mmStrip...
Reference: RBD-2610
Dual-scale measurement in millimeters and inches (25cm/8inch) Integrated PCB design aids: angle gauges, protractor, IC pin spacing tables, etc. High-precision and wear-resistant with R-4 gold-plated finish Ideal for electronic enthusiasts and professionals Compact and portable for convenient use
Reference: RBD-2575
A gender changer is a hardware device placed between two cable connectors of the same type and gender. An example is a cable connector shell with either two female or two male connectors on it (male-to-male or female-to-female), used to correct the mismatches that result when interconnecting two devices or cables with the same gender of connector.