Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0169
Flex length: 5.6 cm. Total Length: 2.2″ (7 cm). Life Cycle : >1 million. Height : 0.43mm (0.017″), Flat Resistance: 10K Ohms ±30%. Power Rating: 0.5 Watts.
Reference: RBD-0276
LOW QUIESCENT CURRENT: 460µA PRECISION VOLTAGE REFERENCE: 1.24V, 2.5V, 5V or 10V SLEEP MODE LOW OFFSET VOLTAGE: 250µV max LOW OFFSET DRIFT: 2µV/°C max
Reference: RBD-0335
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
Reference: RBD-0381
Operating Voltage:6~28 VDC Max Input Voltage:28 V DC Max Current Sensing: 90 A Connecting Type:XT-60 RoboticsBD
Reference: RBD-0189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-0437
Power supply range: 3.7-5V 100mA Resolution: 1280 x 960 Resolution: 600TVL Illumination: 0.5LUX Format: PAL / NTSC Audio Lens: Wide-angle 1.8mm (170º) Image sensor:1/4 CMOS image sensor Sensitive area: 3.5964mm x 2.7084mm Size of the lens: M10
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-0816
Power Supply Voltage: 3.3V~5V Operating Current: <5mA Measuring Distance: 5-100mm VCSEL light source Strong anti-interference Based on DFrobot Fermion VL6180X ToF Distance Ranging Sensor (Breakout)
Reference: RBD-2295
The CC2530 ZigBee series wireless module launched by BEE Iot Technology is a ZigBee RADIO frequency module developed based on TI's CC2530F256 chip. The module can complete ZigBee learning, project application, and industrial production, and can be widely used in the field of short-distance wireless communication networking. It can build powerful network...
Reference: RBD-2505
RS232 Bluetooth Serial Adapter Communication Master-Slave Module
Reference: RBD-2856
Brand: DFRobot
The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application engineers. Solar Power Manager 5V is a small power and high-efficiency solar power management module designed for 5V solar panel. It features as MPPT...
Reference: RBD-2513
Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 25 Kg / 55 lb Approximate Pickup Weight: 5 KgEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and...
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-2514
Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 10 Kg / 22 lb Approximate Pickup Weight: 2 Kg / 4 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through...
Reference: RBD-2563
Introducing the FLYWING Brushless ESC, a high-performance electronic speed controller designed for RC airplane models and hobby planes. This ESC offers reliable and top-quality components to enhance the overall performance of your RC aircraft.
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-0946
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-2126
Manufacturer: China Support TWI and SPI communication Input voltage (recommended) range from 7V to 12V Input Voltage (limit) range from 6V to 20V 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs) Onboard ATmega32u4 microcontroller with 32KB flash memory, 2.5KB SRAM and 1KB EEPROM
Reference: RBD-2327
Brand: DFRobot
In life, remote controllers can be seen everywhere, and most of them are inseparable from the battery. However, we often encounter problems when using the battery, for instance, it is troublesome to replace the battery, batteries are easy to corrode in a humid environment, or the waste batteries may cause serious environmental pollution. Do you know that...
Reference: RBD-2533
This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate analog voltage output.Note:...
Reference: RBD-2508
The ENS160 is a digital multi-gas sensor specifically designed for indoor air quality testing that optimizes the detection of a wide variety of gases and volatile organic compounds (VOCS), including toluene, hydrogen, ethanol, N02 and ozone. The air quality sensor is used in home and building automation, consumer products, electrical and air purification
Reference: RBD-2893
Compatible with MK KK flight control installment pitch of holes Compatible with MK KK flight control system Can connect 1-8 ESC. This has an T plug to connect a battery. This Distribution board has 8 number of the channel to connect different ESCs with 3.5mm Banana Bullet Connectors.
Reference: RBD-2560
Introducing the Dust Sensor - an optical sensing system designed for detecting airborne dust particles using an infrared emitting diode (IRED) and a phototransistor. The diode and phototransistor are diagonally arranged to effectively capture reflected light from dust in the air. Notably, this sensor is highly efficient in detecting very fine particles,...
Reference: RBD-2894
Compatible with MK KK flight control installment pitch of holes Compatible with MK KK flight control system Can connect 1-8 ESC. This has an XT60 plug to connect a battery. This Distribution board has 8 number of the channel to connect different ESCs with 3.5mm Banana Bullet Connectors.
Reference: RBD-2507
Reference: RBD-0341
Specification: battery Capacity : 1100mahbattery Voltage : 11.1 VoltBattery Size : 62*32*25 mmBattery Weight : 84 GramMax continuous discharge : 25CCharge Plug/Discharge Plug : XT60
Reference: RBD-2318
The Speaker module is composed of a power amplifier and a loudspeaker. Sound size can be adjusted by the potentiometer on the circuit board. Enter different frequencies, the speakers produce different tones. Can be carried out by for Arduino encoding and DIY their music box!Product data interfaceusing anti plug,the two sides of the interface are...
Reference: RBD-2774
Enhance your DIY RC robot or FPV setup with the FPV Head Tracker Dual Axis Servo Gimbal Bracket. This dual-axis servo gimbal bracket is designed to securely hold your camera in place, allowing for stable and precise positioning during operation. Crafted from lightweight aluminum alloy, this bracket ensures durability without adding unnecessary weight to...
Reference: RBD-1696
Brand: SparkFun Electronics
Camera Module - pcDuino V3 (2MP) PLL support Windowing support MIPI interface support
Reference: RBD-1870
Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal. Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm. Has RXD, TXD signal indicator light, monitor send and receive status.
Reference: RBD-1919
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-2315
Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm