Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2750
This is a common MOSFET with very low on-resistance and a control voltage (aka gate voltage) that is compatible with any 3-5V microcontroller or mechanical switch. This allows you to control high-power devices with very low-power control mechanisms.
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V
Reference: RBD-2049
Rotation Angle: 300° ±10° Gyroscopic Moment: 10-200gf.cm Rotational Stopper Strength: 3Kgf.cm Push-Pull Strength: 8kGF Max Shaft Wobble: 0.6xL/20MM p-p Max Total Resistance Tolerance: ±20% Residual Resistance: R less than or equal to 10K Ohms 10 Ohms Withstand Voltage: 1 minute at 300V AC Rotation Life: 10000 times Can be used as a 10K contrast...
Reference: RBD-2755
When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220s, but because of the very low Rds(on) of down to 70 mOhms (depending on the Vgs - check the...
Reference: RBD-2059
LDR 20 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.
Reference: RBD-2757
N-Channel logic compatible MOSFET with optoisolation and low Rds(on).
Reference: RBD-2276
Versatile adjustable resistor with precise control and compact size. Cost-effective potentiometer with 5K resistance and single turn. Trimmer potentiometer with yellow casing for easy identification. Commonly used in audio, lighting, and temperature control circuits. Through-hole mounting potentiometer for easy circuit integration.
Reference: RBD-2428
Sorry - we thought that was clever. And while it wasn't really, this potentiometer definitely is! We've seen these in miniature synthesizers. They're bigger than a trim-pot but smaller than a chunky potentiometer. Best of all no knob required! These have a knurled plastic grip with a white stripe marking. Use it as-is, for a low-cost adjustment Comes as...
Reference: RBD-2795
Resistance: 20k Ohm Tolerance: 10 % Temperature coefficient: ±100 ppm/ºC Operating temperature range: -55ºC to +125ºC Mounting type: Through-hole
Reference: RBD-2796
Resistance: 100 Ohm Tolerance: 10 % Temperature coefficient: ±100 ppm/ºC Operating temperature range: -55ºC to +125ºC Mounting type: Through-hole
Reference: RBD-1524
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Reference: RBD-1545
Input voltage 9~40V Output: 5V Maximum output current 2A Efficiency: 76-90% Material: electronic component
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1688
LM1084 5A Low Dropout Positive Regulator
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-1915
Input voltage range : 3-34V DC Output voltage range : 4-35v DC adjustable Output current:3A Voltmeter range:0 to 40V,error +-0.1v Multiple output regulator. One button to switch input and output voltage display. Power-down memory function. Press the button for 3 seconds can turn OFF/ON the LED display.
Reference: RBD-2109
Low dropout voltage Load regulation: 0.2% typical Optimized for Low Voltage On-chip thermal limiting Built-in thermal shutdown Good noise rejection
Reference: RBD-2110
Low dropout voltage Load regulation: 0.2% typical Optimized for Low Voltage On-chip thermal limiting Built-in thermal shutdown Good noise rejection
Reference: RBD-2719
Meet UL, CE requirements, Ultra-thin, ultra-small All voltage input (AC: 90 ~ 264V) Low ripple and low noise Output overload and short circuit protection High efficiency, high power density The product is designed to meet the requirements of EMC and Safety Test
Reference: RBD-2751
Ah the esteemed LD1117, who amongst us has not used this popular low drop voltage regulator? This big chunky regulator will help you get your 4-15V battery or wall adapter down to a nice clean 3.3V with 1% regulation. Perfect for just about all electronics! This is the TO-220 version, with up to 800mA current capability, and has internal current limiting...