Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0550
Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-2099
Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-0665
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-2215
Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.
Reference: RBD-2303
LED peak wavelength: 660nm/880nm LED power supply voltage: 3.3~5V Detection signal type: light reflection signal (PPG) Output signal interface: I2C interface
Reference: RBD-0102
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-2310
1. Reliable Use: With infrared distance detection sensor and touch detection sensor, the robot you designed can adapt to more situation.2. Line Sensing: Has 6 way high sensitivity infrared sensors, 5 way patrol lines and 1 way for road barrier, which can easily identify and track complex and intersecting black and white lines. Output low level for black...
Reference: RBD-2451
Pulse Sensor 3.3-5V Heartbeat Heart Rate Monitor Sensor Easy to use finger-tip heart rate detector module with built-in noise filter and signal amplification.
Reference: RBD-0241
Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical LM35 (working) tested by...
Reference: RBD-0622
Transmission signal processing control chip RCWL-9196 Wide operating voltage range 4.0V to 28.0V Penetrating detection capability, compared with the traditional infrared feeling PIR Adjustable Block time and distance Operating Current: 2.8mA (typical); 3mA (max) Detection Distance: 5-9m Transmitting Power: 20mW (typical); 30mW (max) RoboticsBD
Reference: RBD-2414
This tracking module adopts four tracking probes, and optimized spacing layout. The inner two probes can accurately identify the black line. The outer two probes can assist the inner probe to identify the black line and provide early warning. The car can recognize the 90°curved road and other difficult tracks. Knob-type adjustable resistors plus...
Reference: RBD-2452
This Pulse Sensor is a heart rate sensor designed for Arduino microcontrollers. Development professionals use. The Pulse Sensor Kit brings you all the experience you need, a complete package. The kit includes: A 24inch 3p DuPont line, A soft Velcro Finger Strap, A sensor size sensor ear clip, 4 Velcro dots, and 9 transparent protective dot Pulse Sensor is...
Reference: RBD-0689
Operating Voltage: 2.8 V to 5.5 V Accuracy: ± 1.5°C Zero power resistance: 100 KΩ Operating temperature range: -55 ~ +125 ℃
Reference: RBD-2533
This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate analog voltage output.Note:...
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-0812
Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.
Reference: RBD-2598
Brand: RoboticsBD
Precise Line Following: Navigate black lines on white surfaces with 8 high-resolution sensors. Easy Microcontroller Integration: Connect directly to your microcontroller with digital outputs. Fast and Responsive: Achieve accurate line following even at high speeds. Simple Calibration: Calibrate sensors quickly and easily with a large knob. Versatility:...
Reference: RBD-0830
Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree. Screw Type
Reference: RBD-1243
Resolution: 500dpi Supply current: <60mA Supply voltage: 3.3V Fingerprint image entry time: <1.0 seconds Peak current: <60mA
Reference: RBD-2611
This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate digital I/O-measurable output.
Reference: RBD-0923
Measuring range: temperature -40-80 ℃; humidity 0; 99.9%RH Measurement accuracy (25℃): temperature: + 0.5; humidity: + 2%RH (10; 90%RH) Resolution: temperature: 0.1 ℃, humidity: 0.1%RH Attenuation value: temperature: <1℃ / year; humidity: < 1%RH/ years High precision Capacitive type Full range temperature compensated Relative humidity and...
Reference: RBD-2763
Uses infrared to detect a reflective line on the floor.
Reference: RBD-1042
Operating Voltage: 3.3 ~ 5.5 VDC. Operating Current: 5mA. Interface: PH2.54-3P. Dimensions mm(LxWxH): 98 x 23 x 4. Supports 3-Pin Gravity Sensor interface Analog output. Weight (gm): 15.
Reference: RBD-2836
Operating Voltage: 3.5V-5V Supply Current: 15mA Optimal Sensing Distance: 3mm Designed with the reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn)
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-1062
Temperature detection of the two-dimensional area: 8 × 8 (64 pixels). Digital output (capability of temperature value output). Compact SMD package (adaptively to reflow mounting). RoHS compliant.
Reference: RBD-1648
FPC1020A is a secondary development module for fingerprint recognition designed for SCM. Fingerprint identification capacity: 150 fingerprints, identification time is less than 1 second, can be customized large capacity Capacitive surface array semiconductor fingerprint sensor Support finger 360 rotation recognition Supported Operating Systems: Windows
Reference: RBD-1063
Temperature Control Range(°C): -50 to +110 Resolution @-9.9°C to +99.9°C: 0.1°C Resolution @all temperatures: 1°C Accuracy: 0.1°C Refresh Rate(s): 0.5 Supply Voltage(V): 12 Measuring Inputs: NTC10K Cable Length: 0.5 Meter Output Type: 1 Channel Relay Output Capacity: 10A
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December