Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1347
TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.
Reference: RBD-0396
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD
Reference: RBD-0416
Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output
Reference: RBD-1208
Working Voltage: 5V DC Operating Temperature: -30ºc ~ 85ºc Output high level when received the laser signal Output low level when not receive laser signal. Application: Electronic Circuits
Reference: RBD-1210
Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz
Reference: RBD-0312
Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM
Reference: RBD-0622
Transmission signal processing control chip RCWL-9196 Wide operating voltage range 4.0V to 28.0V Penetrating detection capability, compared with the traditional infrared feeling PIR Adjustable Block time and distance Operating Current: 2.8mA (typical); 3mA (max) Detection Distance: 5-9m Transmitting Power: 20mW (typical); 30mW (max) RoboticsBD
Reference: RBD-1194
Product Name : Optical Sensor Switch Model : RPR220 Color : Black Net Weigh : 3g Material : Plastic, Metal Detection Distance:1-13mm Working Voltage:DC 30V(Max) Output Type:Photo Transistor
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-0683
Operating voltage: DC3-5V Operating current: less than 20mA Sensor Type: Analog Detection Area: 40mmx16mm Operating temperature: 10℃-30℃ Humidity: 10% -90% non-condensing
Reference: RBD-0812
Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.
Reference: RBD-1854
This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.
Reference: RBD-1914
Working voltage 3.3V-5 Output format: digital switching output (0 and 1)A fixed bolt holes for easy installation
Reference: RBD-0685
Detection distance: 2 ~ 30cm Detection angle: 35 ° Comparator chip: LM393 3mm screw holes for easy mounting
Reference: RBD-1913
Onboard LDO Voltage regulator Can be interfaced with 3V3 or 5V Microcontroller. Tap/Double Tap Detection Free-Fall Detection Analog output Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from the motor and other high current electronics Power LED
Reference: RBD-1951
High hardness, Corrosion protection. Waterproofness and High precision. The mode of its output signal:0-5V(Voltage signal). supply voltage: DC 12-24V. Power consumption:Voltage MAX≤0.3W. Start wind speed:0.4-0.8m/s.
Reference: RBD-2087
Voltage 5V Photo interruption module triggers a signal when light is blocked between the opening of the sensor.
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-2009
Digital Auto Counter Meter with Hall Effect Proximity Switch Sensor (Battery Powered) No Power Required Digital Counter Meter Battery Attached Hall Effect Proximity Switch Sensor Connect Hall Effect Proximity Switch Sensor 2 wire to counter terminals 1&2. If the sensor detects a magnet it will start to count.
Reference: RBD-2125
Phototransistor output No contact surface sensing Miniature package
Reference: RBD-2149
Capacity (Kg): 50. Output Sensitivity (mv/v): 1.0±0.1. Nonlinearity (%FS): 0.03. Repeatability (%FS): 0.03. Input Resistance (Ω): 1000. Insulation Resistance (MΩ): ≥5000.
Reference: RBD-2041
Model : KY-040. Type : Incremental Encoder. Cycles per revolution (CPR) : 20. Working voltage : 0 – 5V. Material : PCB + Brass. Mounting Nut Thread diameter: 6.6mm Weight : 10 gm.
Reference: RBD-2095
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 ° **Please be advised that the majority of our customers have left negative reviews for this product. We recommend that you do not make a purchase unless you are absolutely certain that you can...
Reference: RBD-2172
Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD Force Sensitive Resistor Square High Quality
Reference: RBD-0816
Power Supply Voltage: 3.3V~5V Operating Current: <5mA Measuring Distance: 5-100mm VCSEL light source Strong anti-interference Based on DFrobot Fermion VL6180X ToF Distance Ranging Sensor (Breakout)
Reference: RBD-2183
Digital auto counter meter with infrared proximity sensor 24V power supply Adjustable sensing range from 3 to 80 cm Easy to mount chassis Diffuse reflective type light source DC 3-wire NPN-NO output Sensory distance regulator and output LED indicator
Reference: RBD-2214
EMG muscle sensor V3.0 with cable and electrodes Measures the electrical activity of muscles High signal quality for accurate and reliable measurement Adjustable gain and filtering for signal conditioning Compatible with various types of microcontrollers and data acquisition systems Comes with reusable electrodes and a 3.5mm jack cable for easy connection
Reference: RBD-2411
Operating Voltage: 5V Pulse Number for One Circle: 20 Bi-directional Counting with No Limitation
Reference: RBD-2472
Note: Please be aware that once the connector is closed it can't be unlocked
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-2790
The US1881 is an integrated Hall-Effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A Hall-Effect sensor is much smaller, but can handle less current...
Reference: RBD-2851
Shape: Circular. Sensing Area diameter (mm): 30 Min Force: 150 gm. Max Force: 20Kg. Length (mm): 42. Weight (gm): 2.