
Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
The TTP226 is a touchpad detector IC which offers 8 touch key. The touching detection IC is designed for replacing the traditional direct button key with a diverse pad size. Capacitive touch allows electronics to sense when your finger is within a few millimeters of a surface to simulate a button “press” just like how the pushbutton works. Capacitive sensing may be used in any place where low to no force human touch sensing is desirable. The TTP229 is capacitive sensing design specifically for touch pad controls. The device has a built in regulator for the touch sensor. Stable sensing method can cover diversity conditions. Interface control panel links through non-conductive dielectric material. The main application is focused at replacing of the mechanical switch or button. This board can independently handle the 8 touch pads with 8 direct output pins. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Operating Voltage (VDC) | 2.4 ~ 5.5 |
Output Sink Current | 8mA |
Output Pin Pull-up Current | 4mA |
Response Time (Low Power Mode) | 220ms |
Response Time | 60mS |
Length (mm) | 46 |
Width (mm) | 47 |
Height (mm) | 11 |
Weight (gm) | 6 |
Shipment Weight | 0.01 kg |
Shipment Dimensions | 8 × 10 × 1 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino in Bangladesh is BDT 250 You can buy the TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0312
Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Reference: RBD-0663
Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD
Reference: RBD-0752
Onboard trackpad with all mouse function Left+Right click Gaming keys Operate on inbuilt Rechargeable battery Navigation, Volume Rockers and Home key Portable Pocket Size Plug and Play operation, No drivers needed to install Compatible with all Devices and operating Systems. RoboticsBD
Reference: RBD-1167
Resolution:1024 x 600 Display Port: HDMI Touch Type: Capacitive Touch Points:5 points 7-inch IPS screen with a hardware resolution of 1024×600. 5-points capacitive touch control. Using Raspberry Pi, it supports Raspbian / Ubuntu / Kali / Retropie and WIN10 IoT, no need to install any drivers.
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-2364
Pyroelectric Infrared Sensor Human Body Detecting PIR Motion Sensor Module for Arduino MCU 011050 Black Optical Lens
Reference: RBD-0355
Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line
Reference: RBD-0693
Operating Voltage: 3-5.5V Supply Current: ≥ 20mA Optimal Sensing Distance: 3mm Working voltage of 5V, the output of the black line low, white line of high output Uses Infrared Light to Detect Anti-Interference Ability Sensors to adopt TCRT5000 High Sensitivity, Stable Performance Exquisite workmanship, with the indicator Has a fixed bolt hole for easy...
Reference: RBD-2088
Operating Voltage: 5v DC. This module is Small and Simple to use. Digital switch output (0 & 1) High sensitivity Completes the circuit when the module is tilted LED lights up when tilt switch is activated
Reference: RBD-1672
Model Number: P06 Product Name: PIR Sensor Indoor Communication: greater than 20 Meters Detect Angle Side View: 128 degrees Detect Angle Down View: 128 degrees Detect distance: 10 Meters<
Reference: RBD-2414
This tracking module adopts four tracking probes, and optimized spacing layout. The inner two probes can accurately identify the black line. The outer two probes can assist the inner probe to identify the black line and provide early warning. The car can recognize the 90°curved road and other difficult tracks. Knob-type adjustable resistors plus...
Reference: RBD-1206
Scanning Range: 18M Radius Detection Range: 12M Radius 4cm Ultra-thin Ideal for all kinds of service robot. 8000 times sample rate, the highest in the current economical LIDAR industry 360-degree laser range scanning Low Noise, Brushless Motor New Non-contact Drive OPTMAG Original Design, prolong the life-span Class 1 Laser Safety Standard High-speed...
Reference: RBD-2381
HLK-TX510 is a module developed based on artificial intelligence chip TX510, AI computing power 1.2T@8bit/9.6T@binary, supports mixed precision, can quickly detect faces, supports 3D living detection, 3D face recognition, infrared living detection, Visible light live detection, etc., can resist two-dimensional attacks such as photos and videos, and...
Reference: RBD-2313
Sensing range: 3 – 80cm. Input voltage: 5VDC. Current Consumption: 300mA. Digital Output. Cable length: 1m. Diffuse reflective type.
Reference: RBD-1194
Product Name : Optical Sensor Switch Model : RPR220 Color : Black Net Weigh : 3g Material : Plastic, Metal Detection Distance:1-13mm Working Voltage:DC 30V(Max) Output Type:Photo Transistor
Reference: RBD-2147
The built-in 24bit AD converter. Immersion gold PCB, high quality, machine welding process to ensure quality. Power supply: 3 – 5V ( internal low dropout regulator ). Communication modes: Standard the IIC / SPI communication protocol.
Reference: RBD-1740
Operating voltage: 3.3 to 5VDC Ball Rolling type of tilt sensor. This small module is easy to use. A fixed bolt hole for easy installation Wide voltage LM393 comparator
Reference: RBD-0428
Operational Voltage: 3.3V. Ambient Light & RGB Color Sensing. Proximity Sensing. Gesture Detection. Operating Range: 4-8in (10-20cm). I2C Interface (I2C Address: 0x39). RoboticsBD
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0813
Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.
Reference: RBD-2338
High precision Capacitive type Full range temperature compensated Relative humidity and temperature measurement Calibrated digital signal Check out the Authentic DHT22 module
Reference: RBD-1200
Very low supply current Photo-detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light
Reference: RBD-0722
8-Megapixel native resolution high-quality Sony IMX219 image sensor Cameras are capable of 3280 x 2464 pixel static images Capture video at 1080p30, 720p60 and 640x480p90 resolutions All software is supported within the latest version of Raspbian Operating System No Infrared filter making it perfect for taking Infrared photographs or photographing objects...
Reference: RBD-2346
HW-671 WCS1800 Hall Current Sensor Over-current Protection Module Detection
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-1934
Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-2236
Plate Diameter: 20mm Element Diameter: 14mm Plate Thickness: .42mm Lead Length: ~50mm Plate Material: Brass Resonant Frequency (kHz): 6.3 +/- .6kHz
Reference: RBD-2071
Type: Magnetic Sensor Module Mainly Compatible with: Ardunio
Reference: RBD-0368
Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ) Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C Lifespan: >1million times Hysteresis: +10%,(RF+ -RF-)/FR+,1000g...
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0155
Microcontroller: ATmega328 Circuit Operating Voltage: 5V Clock frequency: 16MHz. Digital I/O Pins: 14 8 analog input port: A0 ~ A7. A pair of TTL level serial port transceiver : RX / TX. 6 PWM port: D3, D5, D6, D9, D10, D11. Support serial download.
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0294
Out of stock RAM: 1GB Processor: Broadcom BCM2837 chipset 1.2GHz Quad-Core ARM Cortex-A53 (64Bit) 802.11 b/g/n Wireless LAN and Bluetooth 4.1 (Bluetooth Classic and LE) Storage : SD/MMC/SDIO Power: 5V / 700mA~3A via micro US
Reference: RBD-0280
Tie-points: 170 (10×17)Size: 48 x 35 x 10 mm(LxWxH).Use: experimental, testing, robotMatching jumper, diameter 0.8mmPhosphor bronze nickel plated spring clipsAccepts a variety of wire sizes (29-20 the AWG)**1 pcs Random Color
Reference: RBD-0656
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount.
Reference: RBD-0654
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount. RoboticsBD