How to Place an Order
bKash Payment Method
Nagad Payment Method
Request for Quotation/ International Sourcing
Order Status
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
TSL2561 Luminosity & Infrared Light integrating sensor
Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm
Description:The AD8232 ECG Measurement Module is a neat little chip used to measure the electrical activity of the heart.
RPR-220 is a reflective photosensor. It's lightweight and compact. A built-in visible light filter minimizes theinfluence of stray light. A plastic lens is used for high sensitivity.
Specification: The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Features: Low power consumption Power supply for 2 ~ 5.5V DC
Description: This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area
Product Description 1. Current sensor chip: ACS712ELC-30A. 2. Pin 5V power supply, on-board power light. 3. The module can be measured plus or minus 30A current, Corresponding analog output of 66 mV / A. 4. No test current through, the output voltage is VCC / 2. 5. PCB size: 31 (mm) x13 (mm).
Features:The OPT101 is a monolithic photodiode with on-chip transimpedance amplifier.The ingrated combination of photodiode and transimpedance amplifier on a single chip eliminates the problems commonly encountered in discrete designs, such as leakage current errors, noise pick-up, and gain peaking as a result of stray capacitance.Output voltage increases...
MQ-135 module is widely used in air quality control equipments for buildings/offices, are suitable for detecting of NH3,NOx, alcohol, Benzene, smoke,CO2 ,etc
IR Receiver Diode (3mm) IR receiver diodes can be used in object detection applications like line follower,obstacle detecting robots etc.These were used in our IR Sensor Array.
(Retired) The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. With this kit you will be able to be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. Flir Lepton Installation Instruction...
Gas Sensor(MQ2) module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke or Propane. Due to its high sensitivity and fast response time, measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by the potentiometer.
Brand: Waveshare
Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear with dust density Embedded voltage boost circuit to support wide range of power supply
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version.
(Retired) Add heat-vision to your project and with an AMG8833 Grid-EYE Breakout! This sensor from Panasonic is an 8x8 array of IR thermal sensors. When connected to your microcontroller (or raspberry Pi) it will return an array of 64 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for...
Digital Electronic Weighing SensorScale 5Kg Weight Load Cell 3-12V DC
Chip: BH1750FVI Power Supply: 3.3V - 5V Light Range：0 - 65535 lx(Lux) Sensor Built-in: 16 bit AD converter Size(L x W): Approx. 3.2cm x 1.5cm Direct digital output, bypassing the complex calculation, bypassing the calibration Close to the spectral characteristics of visual Widely used to 1-lux high precision measurement Standard NXP IIC communication...
(Retired) Digital Electronic Weighing Sensor Scale 1Kg Weight Load Cell 3-12V DC
(Retired) Description: his is the LIDAR Lite, a compact high performance optical distance measurement sensor from PulsedLight. The LIDAR Lite is ideal when used in drone, robot, or unmanned vehicle situations where you need a reliable and powerful proximity sensor but don’t possess a lot of space.
(Retired) Features: High-Speed, High-Accuracy Fingerprint Identification using the SmackFinger 3.0 Algorithm Download Fingerprint Images from the Device Read and Write Fingerprint Templates and Databases Simple UART protocol (Default 9600 baud) 360° Fingerprint Recognition Documents: Datasheet Demo Software Garage Door Opener Tutorial (Instructables)...
Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line
The VL53L0 uses ST’s FlightSense technology to precisely measure how long it takes for emitted pulses of infrared laser light to reach the nearest object and be reflected back to a detector, so it can be considered a tiny, self-contained lidar system. This time-of-flight (TOF) measurement enables it to accurately determine the absolute distance to a target
Specification:1. Small size: 11mm*27mm2. Low power consumption: Supply voltage 2.5V ~ 5V, operating current is microamps3. Linear Good4. High Sensitivity5. High stability6. Detection range: 240nm-370nm7. Large angle: 130 degrees8. The Schottky type of photodiode for photoelectric mode
