
Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
TCRT5000L 5 Channel Tracking Sensor Tracking Module Infrared Sensor is based on the TRCT5000 infrared reflection sensor, it is often used to make tracking smart cars. The infrared emitting diode of the TRCT5000 sensor continuously emits infrared rays. When the emitted infrared rays are reflected by the object, they are received by the infrared receiver and output analogue values. The output analogue value is related to the object distance and the colour of the object. The position of the tracking line is judged by calculating the analogue value of the five outputs. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Chip | 74HC14D |
Operating Voltage (VDC) | 3.3 ~ 5 |
Sensor | TCRT5000 |
No. of Channel | 5 |
Measurements of Distance | 0.5 cm ~ 1 cm |
Length (mm) | 100 |
Width (mm) | 20 |
Height (mm) | 12 |
Weight (gm) | 16 |
Shipment Weight | 0.02 kg |
Shipment Dimensions | 7 × 5 × 2 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Line Following Sensor 5 Array.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of Line Following Sensor 5 Array in Bangladesh is BDT 310 You can buy the Line Following Sensor 5 Array at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Very bad . sensitivity was very bad.its good for nothing.i was so frustrated.
You have purchased two line tracking sensors which you have reviewed as negative. It is very unlikely that both sensors have a problem. You need to calibrate the sensor using white and black paper. If you do not calibrate the sensor correctly, it will not work. Please email us to find out more. ask@roboticsbd.com
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-0685
Detection distance: 2 ~ 30cm Detection angle: 35 ° Comparator chip: LM393 3mm screw holes for easy mounting
Reference: RBD-0693
Operating Voltage: 3-5.5V Supply Current: ≥ 20mA Optimal Sensing Distance: 3mm Working voltage of 5V, the output of the black line low, white line of high output Uses Infrared Light to Detect Anti-Interference Ability Sensors to adopt TCRT5000 High Sensitivity, Stable Performance Exquisite workmanship, with the indicator Has a fixed bolt hole for easy...
Reference: RBD-0716
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-1183
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow
Reference: RBD-1241
Color: Black Weight: 120g (each) Outer wheel diameter: 80mm Thickness: 37mm 1 pcs Left and 1 pcs Right Wheel No Connecting Hubs
Reference: RBD-2332
Infrared Photodiode Transmitter 5mm Infrared Photodiode Receiver 5mm
Reference: RBD-0222
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound
Reference: RBD-2351
HLK-LD2410C is a high-sensitivity 24GHz human presence status sensing module developed by Hi-Link Electronics. Its working principle is to use FMCW frequency-modulated continuous wave, to detect human targets in the set space, combined with radar signal processing, accurate human body induction algorithm, to achieve high sensitive human presence status...
Reference: RBD-1856
Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...
Reference: RBD-2236
Plate Diameter: 20mm Element Diameter: 14mm Plate Thickness: .42mm Lead Length: ~50mm Plate Material: Brass Resonant Frequency (kHz): 6.3 +/- .6kHz
Reference: RBD-0338
Brand: Waveshare
Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F
Reference: RBD-1111
This is one open-source Geiger Counter project which could be used to detect nuclear radiation. The schematic and code and other helpful files are listed in this package. All the codes are designed and tested on this kit, these materials are useful for DIY Geiger Counter Kit Nuclear Radiation Detectors or Radiation Monitoring Stations. Note: The kit comes...
Reference: RBD-0426
Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity
Reference: RBD-1202
3-axis magnetic electronic compass. Precise heading information. Operating Voltage: 3 -5 V DC. Driver Chip: HMC5883L. Communication: I2C protocol. Measuring range: ± 1.3-8 Gauss.
Reference: RBD-2364
Pyroelectric Infrared Sensor Human Body Detecting PIR Motion Sensor Module for Arduino MCU 011050 Black Optical Lens
Reference: RBD-2346
HW-671 WCS1800 Hall Current Sensor Over-current Protection Module Detection
Reference: RBD-1942
Actuation Distance : 15 – 25 mm; Connecting cable length: 30 cm. Magnetic sensor alarm, control the switch of the circuit via the built-in magnet Alarm when someone intrudes into your places Can be used in places like apartment, hotel, office, etc.
Reference: RBD-2170
Visualize magnetic fields with ease using the field paper Large size of 100mm x 100mm for a clear and detailed view Micro-encapsulated film enables visualization of magnetic fields Suitable for use with any magnet Lightweight and compact for easy handling and storage
Reference: RBD-1178
Size: 5mm Emitted Color : UV View Angle: About 20 - 25 degree. Luminous Intensity: 800mcd-2500mcd
Reference: RBD-1541
For beginners who are interested in Arduino A complete set of Arduino’s most common and useful electronic components Infrared sensor receiving module Laser sensor module Temperature and humidity sensor module Infrared sensor module 5v relay module Obstacle avoidance sensor module.
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-2229
Highly sensitive and reliable Piezoelectric Vibration Sensor Module Detects vibration and measures acceleration Analog and digital outputs Suitable for industrial control systems, robotics, automotive, and consumer electronics
Reference: RBD-1672
Model Number: P06 Product Name: PIR Sensor Indoor Communication: greater than 20 Meters Detect Angle Side View: 128 degrees Detect Angle Down View: 128 degrees Detect distance: 10 Meters<
Reference: RBD-0391
Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD
Reference: RBD-0354
Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD
Reference: RBD-1914
Working voltage 3.3V-5 Output format: digital switching output (0 and 1)A fixed bolt holes for easy installation
Reference: RBD-2420
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 °
Reference: RBD-1848
Compact Design Country Specific pressure Multiple Displayable Unit Multi-colored, two-part display Alphanumeric display
Reference: RBD-2507
Reference: RBD-0813
Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.
Reference: RBD-1405
Working voltage: 5.00V DC Working current: 40mA (MAX) Response time: <500ms Insulation resistance: 100MΩ (Min) Analogue output: 0~4.5V; Digital output: high/low-level signal (the corresponding threshold can be selected by adjusting the potentiometer) Operating temperature: -20℃~90℃
Reference: RBD-0555
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A
Reference: RBD-0430
Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD
Reference: RBD-1191
Internal filter for PCM frequency. Inner shield, good anti-interference ability. High immunity against ambient light. Improved shielding against electric field disturbance 3.0V or 5.0V supply voltage; low power consumption. TTL and CMOS compatibility. Suitable transmission code:NEC code,RC5 code. Universal receiver. 38 KHz. Infrared remote control receiver.
Reference: RBD-1737
Fastest fingerprint identification in the world, Support multi fingerprint Instant match.
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0911
Entry-level digital multimeters Palm Size 2mF capacitance test (UT33A+) Work safely in CAT II 600V environment
Reference: RBD-1161
Mediocre Quality Lead Name: Tong Kong Wire Diameter: 0.8mm 60/40 Tin/Lead Solder Wire Flux: 2% SWG: 20/22 Net Weight: 10g 0.8mm Melting Temperature 280°C Approx. (Tested by RoboticsBD LAB)
Reference: RBD-0675
Model: MQ-6 Operating Voltage: 5V DC Detecting Range:200-10000 ppm Relative Humidity:<95% RH
Reference: RBD-1298
Overtemperature Protection Logical “0” Input Voltage Up To 1.5 V (High Noise Immunity) Internal Clamp Diodes. Featuring Unit rode L293 and L293D Wide Supply-Voltage Range: 4.5 V to 36 V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs
Reference: RBD-0655
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount. 20mm Height. RoboticsBD
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required