- Raspberry Pi
- Mini Computer/ PC
- Arduino Shield
- Robotics Parts
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- 3D Printer
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Home Automation
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Solderless Large BreadboardA breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard). Because the solderless breadboard for electronics does not require soldering, it is reusable. This makes it easy to use for creating temporary...
GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module
Store Pickup Available!
GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module
10DOF modules (three-axis gyroscope + triaxial accelerometer + triaxial
magnetic + pressure)
Immersion Gold PCB technology adoption
Chip: MPU6050 + HMC5883L + BMP180
Power supply: 3V-5V
Communication: IIC communication protocol (fully compatible with 3-5v
system, including LLC circuit)
2.2 x 1.7cm
1 x BMP180 Sensor Module
Chip: BH1750FVI Power Supply: 3.3V - 5V Light Range：0 - 65535 lx(Lux) Sensor Built-in: 16 bit AD converter Size(L x W): Approx. 3.2cm x 1.5cm Direct digital output, bypassing the complex calculation, bypassing the calibration Close to the spectral characteristics of visual Widely used to 1-lux high precision measurement Standard NXP IIC communication...
Angle Sensor Module for Arduino High-sensitivity angle sensor SW-520D Comparator output, clean signal, great waveform, strong driving ability, more than 15mA Distribution positioner sensitivity adjustment Working voltage: 3.3V~12V Output form: Digital switching output (0 and 1) With fixed bolt hole for easy installation
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
The HMC5983 includes our state-of-the-art, high-resolution HMC118X series magnetoresistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I²C or SPI serial bus allows for easy interface.
Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...
ESP32 Development Board WiFi+Bluetooth Ultra Low Power Consumption Dual Cores ESP-32 ESP-32S Board
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!
Features: Model: YF-S201 Sensor Type: Hall effect Working Voltage: 5 to 18V DC (min tested working voltage 4.5V) Max current draw: 15mA @ 5V Output Type: 5V TTL Working Flow Rate: 1 to 30 Liters/Minute Working Temperature range: -25 to +80℃ Working Humidity Range: 35%-80% RH Accuracy: ±10%
FPM10A Optical Fingerprint Reader Sensor Modules Connect RoboticsBD Fingerprint Shield on top the Arduino Uno R3 Install Adafruit Fingerprint Library (Check Download Tab) Upload this code to Arduino Uno Board (Arduino Code SFG Demo) Run SFG Demo V2.0 Windows Test Software as Administrator
FM Transmitter Module Wireless Microphone Surveillance Frequency 88-108MHz
RCWL-0516 Microwave Radar Sensor Module Human Body Induction Switch Module
Description knock sensor module and a digital interface, built-in LED build a simple circuit to produce percussion flasher.Interface comes with digital LED, will knock sensor connected digital 3 interface, when percussion sensor senses measure to percussive signals, LED flashing light.
VGA OV7670 CMOS Camera Module Lens CMOS 640X480 SCCB W/ I2C Interface Arduino
The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
HX1838 NEC Code Infrared Remote Control Module DIY Kit
MQ-7 Carbon Monoxide Gas Sensor This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance.