![Hobbywing 3A UBEC 5V Hobbywing 3A UBEC 5V](https://store.roboticsbd.com/1916-large_default/hobbywing-3a-ubec-5v-robotics-bangladesh.jpg)
Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
UBEC is an external switching power supply regulator that is separate from brushless ESC. It can obtain DC voltage suitable for the operation of receivers and other devices from a high input voltage (5.5V – 23V) and is stable. RoboticsBD
With up to 3A of output current, it can easily power receivers, gyroscopes, and more than four servos, making it ideal for remote model helicopters, FPV cameras, GoPro brushless gimbals, and large fixed-wing aircraft that use high voltage and multiple servos. Special for FPV image transmission. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Working voltage | 5.5v-35v/lipo 2s-5s |
Continuous Current (A) | 3 |
Instantaneous Current | Min. 4A 20 seconds |
Output Voltage(V) | 5.25V +/-0.5V |
Length (mm) | 50 |
Width (mm) | 30 |
Height (mm) | 20 |
Weight (gm) | 18 |
Shipment Weight | 0.02 kg |
Shipment Dimensions | 7 × 4 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Hobbywing 3A UBEC 5V
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of Hobbywing 3A UBEC 5V in Bangladesh is BDT 890 You can buy the Hobbywing 3A UBEC 5V at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0300
Model: APM 2.8 Arducopter APM 2.8 Flight Controller Input Voltage (V): 12-16 V. Arducopter APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 Arducopter APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 Ublox NEO 7M GPS Tracking sensitivity: 161 dBm Ublox NEO 7M GPS Capture sensitivity : 148 dBm Ublox NEO 7M GPS cold start time:...
Reference: RBD-0324
Wheelbase: 250mm Material: Full Carbon Fiber Weight: 160 gm The arm has multiple motor mounting holes. Equips vibration-free mounting bracket for FPV camera. RoboticsBD
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-0735
Supply Voltage: 7V.Processor: 32 Bit Cortex M4 CoreBus interface (UART, I2C, SPI, CAN).Firmware: Mission planner.Sensors: Gyrometer, Accelerometer, Barometer & MagnetometerMicro SD card to record flight data. RoboticsBD
Reference: RBD-0938
ATmega328P with Arduino bootloader MAX7456 monochrome on-screen display FTDI cable compatible pinout Standard 6 pin ISP header 2 independent power sections with an LED indicator on each Solder jumpers for combining the power sections
Reference: RBD-0959
IC: Atmega644 PA Gyro/Acc: 6050MPU Input Voltage: 4.8V~6.0V AVR Interface: Standard 6 Pin Signal From Receiver: 1520us(5 channels) Signal to ESC: 1520 us
Reference: RBD-1924
Use for convert battery with Deans to XT60 on ESC / charger. Excellent performance, solid and secure connection, safety in use. High quality and compact,easily to add the adapter. No wires design can save more space.
Reference: RBD-0736
Model: 720 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Current: 0.1 A. Rated RPM: 48000. Max Speed: 50000 RPM. Wire Length: 5cm Prop. Length: 55mm
Reference: RBD-0172
FlySky FS-T6 2.4ghz Digital Proportional 6 Channel Transmitter & Receiver System FlySky Introduces its newest 6 channel 2.4GHz system, The FS-T6. After years of success with the CT6B, FlySky presents the new FS-T6 with loads of cool and convenient features making the operation of this transmitter simple and instinctive.
Reference: RBD-0719
Bandwidth (KHz): 500. RF Range (GHz): 2.40 ~ 2.48. No. of channels: 6. Remote controller weight (gm): 400. Power: 6V (1.5V AA*4). Antenna Length: 26mm * 2 (dual antenna). Transmitting Power: ≤ 20dBm. RF Receiver Sensitivity: -105dbm. RoboticsBD
Reference: RBD-2167
Skydroid 5.8G 150CH Full Channel UVC Dual Antenna Control Receiver OTG FPV Receiver Designed for Android phones with UVC support and OTG compatibility Dual antenna design for improved signal stability Channel waveform display and channel adjustment button added for convenience Supports audio playback through the app Automatic scanning mode activated by...
Reference: RBD-0214
FPV Camera Color 480p This Camera Can be used with this Boscam FPV 5.8Ghz AV Transmitter and Receiver for FPV Purpose
Reference: RBD-0725
Model: Emax Simon Series Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S
Reference: RBD-1542
Model: A2212/10T Motor KV: 1400 Max. Efficiency Current: 6-12A No Load Current: 0.7A @10V Current Capacity: 16A/60S LiPO Batteries: 2S-3S
Reference: RBD-1547
The custom-molded case for the Mavic Air 2, with better protection. Small, lightweight and maximum storage capacity Stylish yet indestructible IP34 Water resistant Removable shoulder strap and integrated carry handle for easy transport
Reference: RBD-1546
Model: APM 2.8 APM 2.8 Flight Controller Input Voltage (V): 12-16 V. APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 NEO-M8N GPS Module Dimensions: Outer diameter 54mm NEO-M8N GPS Module Ready to Connect to All APM FC with 5-pin connector Attached NEO-M8N GPS Module Receiver...
Reference: RBD-1570
Length: 9″. Pitch: 4.7″. Weight: 20 gm. Shaft Diameter: 7.86 mm. Total Length: 9 inch / 225 mm. Material: ABS
Reference: RBD-0437
Power supply range: 3.7-5V 100mA Resolution: 1280 x 960 Resolution: 600TVL Illumination: 0.5LUX Format: PAL / NTSC Audio Lens: Wide-angle 1.8mm (170º) Image sensor:1/4 CMOS image sensor Sensitive area: 3.5964mm x 2.7084mm Size of the lens: M10
Reference: RBD-2153
Framework: 12N14P KV: 980KV LiPO Batteries: 2-3S Max. thrust: 880gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-0946
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-0335
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-0825
Improved Locking Gold Plated Connectors tip Color: Red High-Quality built and Material Good resistance to Temperature & High Amp. Current
Reference: RBD-0324
Wheelbase: 250mm Material: Full Carbon Fiber Weight: 160 gm The arm has multiple motor mounting holes. Equips vibration-free mounting bracket for FPV camera. RoboticsBD
Reference: RBD-0826
PolyMax 3.5mm Gold Connectors 3.5mm sprung gold connectors handle the large current, 50A+ systems. perfect for 3500mAh or larger capacity batteries
Reference: RBD-0940
Good Quality Type: Male-Female Plated Connectors Length: 10 cm Color: Red and Black
Reference: RBD-2506
The SF Racing F3 flight controller is designed to provide high performance flight experience for the hobbyists. With verified sensor algorithm, it provides incomparable I/O capabilities. The SF Racing F3 runs a next-generation 32-bit STM32F303CCT6 processor, an MPU6500 accelerometer and a gyroscope sensor, all high integrated on a lightweight PCB to...
Reference: RBD-1569
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-0571
Item Name: T plug Quantity: 1 male & 1 female Body Material: Brass and gold plated Internal Material: Nylon/PA Internal Resistance: 0.4mΩ
Reference: RBD-1074
Frequency: 5.8G 48CH Transmitting Power: 25mW/100mW/200mW/OFF(Pitmode) Power supply: DC 3-5.2 V (1S) Current(4.2v): 320mA (25mW) /400mA(100mW) /460mA(200mW) Weight: 4.4g Standard size: 18.03*16.83*16.55mm
Reference: RBD-0381
Operating Voltage:6~28 VDC Max Input Voltage:28 V DC Max Current Sensing: 90 A Connecting Type:XT-60 RoboticsBD
Reference: RBD-1055
Length: 5″. Pitch: 4.5″. Weight: 27 gm. Shaft Diameter: 5mm. Total length: 5 inch / 125 mm. Material: Poly-Carbonate.
Reference: RBD-0718
Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery) (not included).
Reference: RBD-0379
TS832 RC832 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V
Reference: RBD-1073
3.7V 600mAh 25C Lipo battery Product Type: Lithium Polymer Battery Pack The LiPo battery has matched resistance. Good Temperature Control. Minimum weight in Class
Reference: RBD-1537
Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter: 2mm EL light length: 3M Lifetime: >12,000 hours Color: White
Reference: RBD-1735
Original Waveshare IPS screen,1280x800 high resolution Capacitive touch control supports up to ten-points touch When works with Raspberry Pi, supports Raspbian, Ubuntu, single touch, and driver free When working as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free Supports Banana Pi, Banana Pro, comes with Lubuntu,...
Reference: RBD-0660
Material: glass fiber Can connect 1-4 ESC. RoboticsBD This has an XT60 plug to connect a battery.
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-0994
KCD1-101 10 Amp Rocker Switch 2 pin, ON-OFF, black and red color of button for your choice
Reference: RBD-0988
Hold 3 standard 18650 batteries. Wire Length: 15 cm. Output: 11.1 V. Dimension (Appro.) : 76 x 60 x 18 mm. Weight: 18 gm. High-quality plastic material
Reference: RBD-1145
Version 1.4 HDMI to micro HDMI cable Supports 480i ,480p, 720p, 1080i, 1080p, 1440p resolution Cable Length: 1.5m Color: Black Application: Mulitimedia
Reference: RBD-0999
Holds 4 AA batteries The standard 5.5×2.1mm barrel jack at the output. Easy install, convenient to use. Dimensions mm (LxWxH): 62 x 58 x 15 Weight: 15 gm Material: Plastic Internal Connection: Series