- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Home Automation
- Learning Kit
- Arduino Shield & Module
- Robotics Parts
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- CNC & Laser Cutter
Emax Simon Series 30A ESC
- Model: Emax Simon Series
- Burst Current: 40A (up to 10Sec)
- Input Voltage(V): up to 16V
- Constant Current: 30A
- BEC: 5V /2A
- Suitable Batteries: 2 ~ 4S
Store Pickup Available!
Free Ship Over 5000 BDT
Emax’s SIMON Series 30A ESC is designed specifically for FPV racing. The Emax series is a line of high-performance and low-cost ESCs for drone motors. Emax’s ESC’S are 100% guaranteed original and genuine products for the beginner who wants to learn how to build a drone.
EMAX Simon SERIES 30A ESC is a brushless dc motor speed controller. The low output resistance greatly enhances power stability because The ESC is adapting a 2-4S LiPo battery which improves good battery life. The EMAX Simon ESC is programmed to start the brushless dc motor. This ESC has a greater current handling capacity which is 30A continuous and the peak current is 40A for the last 10 seconds only.
- Based on Simon firmware, further optimized to the perfect drive performance.
- Low-voltage protection, over-heat protection, and throttle signal loss protection.
- Separate power supply for MCU and BEC, enhancing the ESC’s ability to eliminate magnetic interference.
- Parameters of the ESC can be set via a program card or transmitter.
- Throttle range can be set to be compatible with different receivers.
- Equipped with built-in linear BEC or switch BEC.
- Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.
|Model||Emax SIMON Series 30A|
|Burst Current (A)||40|
|Constant Current (A)||30|
|Suitable Lipo Batteries||2 ~ 4S|
|Dimensions (mm) LxWxH||52 x 26 x 7|
|Application||BLDC Motors, Multirotor, RC Planes etc.|
|Shipment Weight||0.03 kg|
|Shipment Dimensions||8 × 6 × 3 cm|
Package Includes :
1 x Emax SIMON Series 30A ESC
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
IC: Atmega644 PA Gyro/Acc: 6050MPU Input Voltage: 4.8V~6.0V AVR Interface: Standard 6 Pin Signal From Receiver: 1520us(5 channels) Signal to ESC: 1520 us
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
4 poles 12 slot Hi-torque motor design CNC machined 6061 T6 windings maximizes efficiency High RPM ABEC5 oversize bearings Universal fit, fit all 1/10 brushless cars-multi-mounting system for M3 screws Precision balanced rotor, smoothness for best reliability and maximum RPM
High-Quality Carbon fiber Material Frame Comes With Landing Gear Power Distribution Board Pre Installed Easy to Assemble kit
Manufacturer: Gravitech Operating Voltage (logic level): 5V 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch.
Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery) (not included).
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm