
Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
T-Connectors Male-Female Pair. Pack includes 1 Male and 1 Female connector. These connectors are made from Nylon, making them very tough and difficult to melt, even with the worst of soldering skills. RoboticsBD
These are for those customers still stuck with the old t-connector. We suggest all customers upgrade to the new XT-60 connector where possible as that is the connector attached to nearly all our batteries, ESC, charger, and models. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Connector Type | T style |
Voltage Rating | 50V |
Current Rating | 16A |
Color | red |
Gender | Mail-Female Pair |
Body Material | Brass and gold plated |
Internal Material | Nylon/PA |
Internal Resistance | 0.4mΩ |
Recommend Use Times | 1000 times |
Max. RC/MC | 36A/60A |
Temperature Resistance | -20°C ~ 120°C |
Pulling Force/500 | 25N |
Weight | 5.6g/Pair |
Shipment Weight | 0.02 kg |
Shipment Dimensions | 5 × 3 × 2 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x T Connector Male-Female Pair.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of T Connector Male-Female Pair in Bangladesh is BDT 40 You can buy the T Connector Male-Female Pair at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0651
Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.
Reference: RBD-0657
Saves space due to the small design Screw connection with tension sleeve Maximum contact force ensures a low-temperature rise Connection in accordance with EN-VDE Standard. RoboticsBD L Type 2pin/way 5.08mm Screw
Reference: RBD-0825
Improved Locking Gold Plated Connectors tip Color: Red High-Quality built and Material Good resistance to Temperature & High Amp. Current
Reference: RBD-0826
PolyMax 3.5mm Gold Connectors 3.5mm sprung gold connectors handle the large current, 50A+ systems. perfect for 3500mAh or larger capacity batteries
Reference: RBD-0942
Manufacturer: AMASS Type of connector: DC supply Connector series: XT60H Kind of connector: Female Number of pins: 2
Reference: RBD-1571
Length: 10″. Pitch: 4.5″. Weight: 25 gm. Shaft Diameter: 9.5 mm. Total Length: 10 inch / 250 mm. Material: ABS
Reference: RBD-1291
12MP / 2.7K Quad HD 3-Axis Gimbal Camera Up to 30 Minutes of Flight Time Stream HD Video from up to 2.5 Miles Remote Controller & 3 Batteries Included Mavic Mini is discontinued by DJI
Reference: RBD-2153
Framework: 12N14P KV: 980KV LiPO Batteries: 2-3S Max. thrust: 880gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-0735
Supply Voltage: 7V. Processor: 32 Bit Cortex M4 Core Bus interface (UART, I2C, SPI, CAN). Firmware: Mission planner. Sensors: Gyrometer, Accelerometer, Barometer & Magnetometer Micro SD card to record flight data. RoboticsBD
Reference: RBD-1925
Use for convert battery with Deans to XT60 on ESC / charger. Excellent performance, solid and secure connection, safety in use. High quality and compact,easily to add the adapter. No wires design can save more space.
Reference: RBD-1532
Small size and light weight, only 183g, easy to carry and more comfortable to wear. Double antenna reception to make the signal more stable. Built-in 3.7V/1200mAh high-capacity Li-ion polymer battery, and the longer time to enjoy your flying. Built-in super sensitiveness 5.8GHz 40ch receiver, especially with raceband. It’s more convenient, easier and...
Reference: RBD-0378
Model: Eachine 1000TVL 1/3 CCD Lux: 0.08Lux/ F1.2 Sensor: 1/3 “CCD Format: NTSC/PAL(Free switch) Resolution: a.Ultra High Definition 1000TVL b.PAL: 976H X 582V c.NTSC: 976H X 494V Lens: 2.8mm IR coated. RoboticsBD FOV: 110 °
Reference: RBD-0324
Wheelbase: 250mm Material: Full Carbon Fiber Weight: 160 gm The arm has multiple motor mounting holes. Equips vibration-free mounting bracket for FPV camera. RoboticsBD
Reference: RBD-1543
Constant Current: 30A (Max 40A<10s). BEC: 5V 3A. Input Voltage: 11.1 ~ 11.7 V. Li-Po battery: 2S ~ 3S. Ni-MH 4-10 CELLS Auto Detect. Current stock is without connector
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-1569
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-0725
Model: Emax Simon Series Burst Current: 40A (up to 10Sec) Input Voltage(V): up to 16V Constant Current: 30A BEC: 5V /2A Suitable Batteries: 2 ~ 4S
Reference: RBD-0380
Eachine VR D2 40CH 5 Inches 800 x 480 Raceband 5.8G Diversity FPV Goggles with DVR Lens Adjustable
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-1387
Memory Size: 128 Gigabyte Card Type: Micro SD Speed: up to 95MB/s Class: 10 High-speed Card can be used for both Mobile phone and Raspberry Pi
Reference: RBD-0940
Good Quality Type: Male-Female Plated Connectors Length: 10 cm Color: Red and Black
Reference: RBD-0946
Supported Receiver Input Signal: PPM, SBUS, DSM Support PPM, SBUS, DSM receiver input signal Battery voltage detection and buzzer interface Large current NMOS transistors, operating current can reach 10A or higher Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Reference: RBD-1546
Model: APM 2.8 APM 2.8 Flight Controller Input Voltage (V): 12-16 V. APM 2.8 Flight Controller Processor: ATMEGA2560 and ATMEGA32U-2 APM 2.8 Flight Controller Dimensions (mm) LxWxH: 70 x 45 x 15 NEO-M8N GPS Module Dimensions: Outer diameter 54mm NEO-M8N GPS Module Ready to Connect to All APM FC with 5-pin connector Attached NEO-M8N GPS Module Receiver...
Reference: RBD-1321
Product Type: Multi Purpose Propeller: 10 Inch
Reference: RBD-1314
12MP / 2.7K Quad HD 3-Axis Gimbal Camera Up to 30 Minutes of Flight Time Stream HD Video from up to 2.5 Miles Remote Controller & 3 Batteries Included Mavic Mini is discontinued by DJI
Reference: RBD-0214
FPV Camera Color 480p This Camera Can be used with this Boscam FPV 5.8Ghz AV Transmitter and Receiver for FPV Purpose
Reference: RBD-0825
Improved Locking Gold Plated Connectors tip Color: Red High-Quality built and Material Good resistance to Temperature & High Amp. Current
Reference: RBD-0381
Operating Voltage:6~28 VDC Max Input Voltage:28 V DC Max Current Sensing: 90 A Connecting Type:XT-60 RoboticsBD
Reference: RBD-1072
Material: Carbon Fiber Wheelbase: 95mm Upper plate thickness:1mm Bottom plate thickness:1.5mm Net Weight: 8.9g Motor size: 8.5x20mm.
Reference: RBD-1055
Length: 5″. Pitch: 4.5″. Weight: 27 gm. Shaft Diameter: 5mm. Total length: 5 inch / 125 mm. Material: Poly-Carbonate.
Reference: RBD-0733
This RP-SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is the slightly longer length of 150mm (compared to 100mm). We found that the extra 50mm makes all the difference when working with an enclosure. U.FL Termination RP-SMA Termination 150mm Length
Reference: RBD-0743
Wheelbase: 550mm Weight: 550g/720g(without/with gimbal) Adopts S800 upward tilt arm design – Plastic injection moduling Ensures hardness and lighter weight – Brushless gimbal compatible for FPV It comes with PCB center board of soldered The arm equips support ridges for better and faster forward flight. Features pre-threaded brass sleeves.
Reference: RBD-1389
Memory Size: 64 Gigabyte Card Type: Micro SD Speed: up to 95MB/s Class: 10 High-speed Card can be used for both Mobile phone and Raspberry Pi
Reference: RBD-0556
Framework: 12N14P KV: 1400KV LiPO Batteries: 2-3S Max. thrust: 930-940gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-0437
Power supply range: 3.7-5V 100mA Resolution: 1280 x 960 Resolution: 600TVL Illumination: 0.5LUX Format: PAL / NTSC Audio Lens: Wide-angle 1.8mm (170º) Image sensor:1/4 CMOS image sensor Sensitive area: 3.5964mm x 2.7084mm Size of the lens: M10
Reference: RBD-2286
Flexible-SC(FR) cable with 1x0.4 rm gauge size, Black color, and flame-retardant insulation material. Designed for electrical use in a variety of applications.
Reference: RBD-0674
Model: MQ-5 Operating Voltage: 5V DC Operating Temparature:-20~40 degree celcius
Reference: RBD-1258
Model No: XW Power Eagle Lipo 1000mAh 7.4V 2S 25C Lipo Battery (T Plug Connector) Weight: 76 gm. Voltage: 7.4V. Dimensions : 26x34x72 (mm ). Max Continuous Discharge : 25C(25A). Balance Plug: JST-XH. Max Burst Discharge: 90 C (50A). Discharge Plug: T-Plug.
Reference: RBD-0718
Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery) (not included).
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-1340
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-0999
Holds 4 AA batteries The standard 5.5×2.1mm barrel jack at the output. Easy install, convenient to use. Dimensions mm (LxWxH): 62 x 58 x 15 Weight: 15 gm Material: Plastic Internal Connection: Series
Reference: RBD-0429
High precision determination accurate to 1 Lu for different lights Operating Voltage: 3-5VDC Built-in 16bit A/D converter I2C interface