Length: 8.5 inches (Medium)
Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire
You will get only one pcs.
Arduino UNO in Bangladesh
The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Parameter Settings:（Rotate one grid clockwise is "+" Rotate one grid counter-clockwise is "-", Press the knob. is"Confirm"） 1. Press and hold the knob for 2 seconds to enter the parameter setting, Display parameter number "F001", Then press "Confirm ", to Set the value of parameter "F001", =0 is coarse tuning; =1 Fine tuning; Then press "Confirm" to save its value. 2. When the parameter number "FXXX" is displayed, "+" "-" Rotation modification parameter number; Enter the password first "+ - - +", To enter the F002 parameter; Enter the password first "+ - + -", To enter the F100 parameter; Enter the password first "- + - +", To enter the F200 parameter.
DESCRIPTION
Sensor module for measuring current. Both AC and DC, up to 20A can be measured. The output is a linear voltage between 0 – VCC, centered around VCC/2 at 0A. The load is connected in series to the screw terminal.
* Dimensions: 31 x 13mm* Supply voltage: 5V* Sensitivity: 185mV/A* Sensor: ACS712ELC-05B
DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator
Input voltage: DC 3 V to 6 VInput current: 2 A - 5 AHigh-pressure type: the type of pulse currentOutput voltage: 400000 v(Please pay attention to safety)High-pressure discharge distance between 10 mm - 20 mmThe output high voltage wire length: 100 mm
AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino
This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals. The maximum current that can be detected can reach 5A, and the present current signal can be read via analog I / O port.
ZMCT103C AC current Sensor is the best for the purpose of the DIY project and industrial application, where we need to measure the accurate AC current with current transformer. This is an perfect choice to measure the AC current using Arduino/ESP8266/Raspberry Pi like an opensource platform. In many electrical projects, engineer directly deals with...
DESCRIPTION
Sensor module for measuring current. Both AC and DC, up to 5A can be measured. The output is a linear voltage between 0 – VCC, centered around VCC/2 at 0A. The load is connected in series to the screw terminal.
* Dimensions: 31 x 13mm* Supply voltage: 5V* Sensitivity: 185mV/A* Sensor: ACS712ELC-05B
It is a Voltage Transmitter/Power Supply Module, Power supply: DC 7~36V (if the output needs to be 10V, the input must be over 12V), In the process of signal transmission circuit voltage signal will increase transmission distance becomes weak, the transmission can be avoided using weak electric current signal. suitable for in the industrial instrument...
Product Description
1. Current sensor chip: ACS712ELC-30A. 2. Pin 5V power supply, on-board power light. 3. The module can be measured plus or minus 30A current,
Corresponding analog output of 66 mV / A. 4. No test current through, the output voltage is VCC / 2. 5. PCB size: 31 (mm) x13 (mm).
EL wire is a thin copper wire coated in a phosphor that glows a 360 degree unbroken light when an alternating current is applied to it. It is bendable as a thin neon tube which makes it ideal for flexible decoration. It is great for car decoration, parties, camping and so on.
AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino
This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals. The maximum current that can be detected can reach 5A, and the present current signal can be read via analog I / O port.
