Arduino MicroSD Card Module

Reference: RBD-1541

37 In 1 Sensor Module Board Set Kit For Arduino with Box

37 IN 1 BOX Sensor Kits /37 SENSOR KIT For Arduino with Plastic Box

Reference: RBD-986

4x4 Keypad - 16 Key - Matrix Membrane Type

4 x 4 Matrix Membrane Keypad Size: 7cm X 7.5cm 8 pin connector Adhesive mounting (sticker on the back side) Maximum Circuit Rating: 35VDC, 100mA Operation Temperature: 0 to +60 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours Fexible Circuit Length: Approx. 3.3 inch / 83 mm

Reference: RBD-1573

Five-Way Navigation Button Module 5D Joystick Independent Keyboard Switch Button Single Chip

Five-Way Navigation Button Module 5D Joystick Independent Keyboard Switch Button Single Chip

Reference: RBD-384

MAX7219 Red Dot Matrix Module MCU Control Display Module DIY Kit For Arduino

Soldering is required

Reference: RBD-306

Torobot 32 Channel USB UART Servo Motor Controller

32 Channel USB UART Servo Motor Controller  Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.

Reference: RBD-31

Jumper Wire 40 Pcs Set

3 Types Available 1. Male to Male  2. Male to Female 3. Female-Female

Reference: RBD-1381

Opto-Isolator ILD213T

This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to...

Reference: RBD-1575

5V 2 Channel Solid State Relay (SSR)

A two-channel relay module (HCMODU0115) featuring 2x G3MB-202P solid-state relays. This module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller. A resistive type fuse is provided on the module to help protect excessive current draw.

Reference: RBD-1759

Brand: Waveshare

E-Ink Electronic E-paper Display Screen Module 200x200, 1.54inch

This is an E-Ink display module, 1.54inch, 200x200 resolution, with embedded controller, communicating via SPI interface, supports partial refresh. Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on....

Reference: RBD-1684

Arduino Pro Mini PLC Relay Board

Pro Mini PLC Relay Board DC 12V 8 Channel Relay Shield Module Delay Timer Switch Board for Arduino

Reference: RBD-413

Data Logger Module Logging Shield Data Recorder Shield for Arduino

SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card Real time clock (RTC) keeps the time going even when the Arduino is unplugged.

Reference: RBD-1332

I2C Graphic 128x64 LCD Adapter

This is I2C adapter for Graphic LCD 128x64, very suitable for interactive work with Arduino, Raspberry. In this adapter used driver MCP23017. For instruction and libraries you can find information here: www.gammon.com.au/forum/?id=10940 For change I2C adress you can folow infromation on bottom side of board.  Control of backlight: Normal backlight use...

Reference: RBD-1354

Jumper Wire Single Medium

Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.

Reference: RBD-1353

Jumper Wire Single Long

Length: 12.5 inches (Long) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.

Reference: RBD-1369

Micro Limit Switches

KW11-3Z bearing microswitch. 5A;250VAC 

Reference: RBD-987

Arduino NANO I/O Extension Shield

Arduino NANO I/O Extension Shield

Reference: RBD-1217

Nextion NX3224T024 - Generic 2.4" TFT LCD Touch Display

Nextion is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to Internet of thing (IoT) or consumer electronics field.

Reference: RBD-1180

4 Channel 5V Relay Shield for Arduino

Relay Shield (ie 5V Quad Relay Module) is a small current signal control power equipment commonly used electronic module, enabling high-power single-chip control devices are widely used in SCM system to make smart home project; and can be directly plugged into the compatible the use of various types of motherboards, eliminating the patch cable troubles.

Reference: RBD-579

GPS GSM GPRS SIM808 Module (Arduino Compatible)

SIM808 module is a GSM and GPS two-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation. 

Reference: RBD-353

0.96" Inch I2C OLED Display Yellow

Size: 0.96 Resolution: 128X64 Color: Blue, Yellow Viewing angle: greater than 160 degrees Low power consumption: 0.04W during normal operation Support wide voltage: 3.3V-5V DC Working temperature: -30-80 degrees Volume: 27MM * 27MM * 4.1MM Driver IC: SSD1306 Communication: IIC, only two I / O ports Backlight: OLED self light, no backlight

Reference: RBD-1367

RGB Full color LED SMD Module

The KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout. Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP8266. RGB full color LED Module KY-009 for Arduino, emits a range of colors by mixing red, green and blue. The amount of each primary color is adjusted using PWM.

Reference: RBD-699

1.8" inch TFT LCD Display module ST7735S 128x160

1.8-inch color screen,support 65K color display,display rich colors 128X160 resolution, clear display Using the SPI serial bus, it only takes a few IOs to illuminate the display With SD card slot for convenient function expansion Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms Military-grade process standards,...

Reference: RBD-1761

Cable For Arduino UNO/MEGA (USB A to B)-3.2 Feet/1Meter

Cable For Arduino UNO/MEGA (USB A to B)-3.2 Feet/1Meter  Length: 3.2 Feet/1Meter  Product Details Product Type: USB Cable for Arduino Mega or Uno, Printer, scanner, and any other peripherals to a computer Used for: data transfer from computer to any other devices Colour: blue, transparent Data transfer: high speed and error-free Connector type: A to B...

Reference: RBD-702

1 Channel 5V Relay Board Module

This is a 5V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) . **Relay Brand is different from the picture as per stock

Reference: RBD-438

New ENC28J60 Ethernet LAN Network Module For Arduino

Chip board ENC28J60-I/SOThe board 25MHZ crystalThe network interface board HR911105A3.3 V power supply pinThe board size : 56 (mm) x 34 (mm)

Reference: RBD-396

Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

Specification: Electrical parameters: JSN-SR04T Operating voltage: DC 5V Quiescent current: 5mA Total current work: 30mA Acoustic emission frequency: 40khz Farthest distance: 4.5m Blind: 25cm 

Reference: RBD-1331

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V General information This is the good old AC Dimmer, but with 2 channels. This one also can control the alternating current voltage in the same way. It can be used with lamps, elements, fans, pumps, air cleaners etc. So it’s the same thing, but twice bigger. In the tutorial, you can...

Reference: RBD-1769

Mini MP1584EN DC-DC BUCK Adjustable Step Down Module

Mini DC 6.528V to DC 0.8V-20V MP1584 3A DC-DC Step-down BUCK Module

Reference: RBD-345

ESP8266 ESP-01 WIFI Wireless Transceiver Send Receive LWIP AP+STA M70

ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is a highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module. 

Reference: RBD-1065

Arduino CNC Shield V3

This shield is designed to allow you to control a CNC router or milling machine from an Arduino board. It contains 4 driver sockets which allow compatible  A4988 or DRV8825 driver modules to be inserted  providing the ability  to drive 3 stepper motor axis (X,Y, & Z) plus an optional 4th auxiliary motor. Additional connectors provide easy connection...