Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
This is a 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module 5V/3A 3V/1A Micro USB for Arduino ESP32 ESP8266. This mobile power supply has a built-in lithium battery protection IC, which has overcurrent, overvoltage, Undervoltage protection, and the module is a portable mobile power supply that supports 3V/1A and 5V/3A two voltage outputs.
Installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative Or Installation errors will burn out the module. The battery voltage works normally from 3.2V to 4.2V. 5V voltage output rated current is 3A, maximum support 3.6A current (not recommended for overload, easy to damage the module, speed up the service life), the output of current depends on the quality of the 18650 battery.. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Output Voltage(V) | 3V/5V |
Output Port Type | USB or expansion port |
Input Port | MICROUSB |
Conversion efficiency(%) | 95 |
Length (mm) | 100 |
Width (mm) | 50 |
Height (mm) | 20 |
Weight (gm) | 38 |
Shipment Weight | 0.042 kg |
Shipment Dimensions | 10 × 8 × 1 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 2x 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of 2x 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module in Bangladesh is BDT 750 You can buy the 2x 18650 Lithium Battery Shield V8 Mobile Power Expansion Board Module at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0837
Capacity (mAh): 960-1500 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life ***It's a clone battery so the ampere couldn't be guaranteed. RoboticsBD
Reference: RBD-0983
Capacity (mAh): 960-2000 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life SMALL SUN
Reference: RBD-1694
Capacity (mAh): 960-2000 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life Genuine SMALL SUN
Reference: RBD-1776
Capacity (mAh): 1000mAh (approx.) Rechargeable Times: Up To 1000 Times Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life 1 pcs 3.7V 18650 Rechargeable Battery
Reference: RBD-0550
Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD
Reference: RBD-2307
This speaker is a great addition to any audio project where you need 8 ohm impedance and 3W or less of power. We particularly like this speaker as it is small and enclosed for good audio volume and quality. It has a handy JST 2PH input cable to add audio to your displays and other projects (this connector is part of the JST-PH series which is ~2.0mm...
Reference: RBD-2157
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.
Reference: RBD-1137
Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI,...
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-2470
3 Watt 8 Ohm Mini Speaker for Electronics Project with JST-PH2.0 Interface
Reference: RBD-2065
Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts
Reference: RBD-1815
I/O Isolation for MCUs (Micro Controller Units) Noise Suppression in Switching Circuits Driving Port Signal Voltage: 3.6-24V Output Port Voltage Port: 3.6-30V Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.
Reference: RBD-2039
Product Name:DY-SV5W Voice Playback Module Product Number:DY-SV5W Work Voltage:DC 5V Working Temperature range:-20℃~85℃ Working Humidity range:0%-95%RH Size :35*35*4.5mm
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-2057
Access multiple interfaces simultaneously Serial Communication Smaller Volume Wide Range of applications You can access the sample code and documents for this product by visiting your order history page.
Reference: RBD-0986
Ultra-thin design & adhesive backing provides easy integration to any project. Excellent price-performance ratio. Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting.
Reference: RBD-2559
This Rich Shield has various sensors, buttons, LEDs, a potentiometer, segment display and buzzer. Specifications: Suitable for Uno, Mega, Leonardo and other 5V Arduino's that use the Uno R3 pin layout Works on 5V Has various parts to learn the basics with Arduino IR Remote Control is included Handy I2C and UART (RX/TX) pins available
Reference: RBD-2092
Product Type: LED Shape: Round LED 5mm DIP type Color: pink yellow-green (high brightness) Lens type: white mist Standard Forward Voltage:3.0-4 .5 V
Reference: RBD-2447
Ultra small module converts 4.5 – 24V input down to a 0.8 – 22V output @ up to 2A.
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-2100
Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.
Reference: RBD-1928
Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.
Reference: RBD-1871
5V single power supply. Wave frequency adjustable 0-400Hz adjustable frequency pure sine wave. Unipolar and bipolar modulation mode. External 12MHz crystal oscillator. PWM carrier frequency 23.4KHz. Voltage, current, temperature feedback real-time processing. Overvoltage, Undervoltage, overcurrent, overheating protection function. Pin set soft-start mode...
Reference: RBD-1398
Brand new and high quality. 1-Channel Relay interface board, Equipped with high-current relay : 15A @ 125V AC or 10A @ 250V AC Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM) **Relay Brand is different from the picture as per stock
Reference: RBD-2362
Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...
Reference: RBD-2243
Wearable e-textile technology. Designed with large sew tabs Button Board
Reference: RBD-2244
Wearable e-textile technology. Designed with large sew tabs Slide Switch
Reference: RBD-0579
Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep...
Reference: RBD-2541
Brand: DFRobot
This is the latest voice recorder module with integrated record and play functions. Easily record your voice by pressing the record button, speaking and then releasing the button when finished. The module is able to playback 10 seconds in total. Connect an 8Ω 3W speaker or an external active speaker for voice output. The module also has a 3 pin digital...
Reference: RBD-2428
Sorry - we thought that was clever. And while it wasn't really, this potentiometer definitely is! We've seen these in miniature synthesizers. They're bigger than a trim-pot but smaller than a chunky potentiometer. Best of all no knob required! These have a knurled plastic grip with a white stripe marking. Use it as-is, for a low-cost adjustment Comes as...
Reference: RBD-2076
Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150
Reference: RBD-1834
PT100 to 0-5V Converter Voltage Signal Conditioner PCB-mounted
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-1266
It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green, as well as 2 matching...
Reference: RBD-1792
Diameter 3mm and Length 10 (M3 x 10) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-2199
Compatible with the Arduino IDE, making it easy for beginners to start using Smaller and cheaper than traditional Arduino boards Powered by a 16.0 MHz microcontroller Fully assembled except for headers, allowing for easy soldering Great for projects where size and cost are a concern Perfect for beginners to jump into electronics Can be used for a variety...
Reference: RBD-1191
Internal filter for PCM frequency. Inner shield, good anti-interference ability. High immunity against ambient light. Improved shielding against electric field disturbance 3.0V or 5.0V supply voltage; low power consumption. TTL and CMOS compatibility. Suitable transmission code:NEC code,RC5 code. Universal receiver. 38 KHz. Infrared remote control receiver.
Reference: RBD-1637
4mm Banana Plug Jack Socket Male Female Binding
Reference: RBD-1791
Diameter 3mm and Length 12 (M3 x 12) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-2104
40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use