
Reference: RBD-1354
Jumper Wire Single Medium
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
This is the RGB and Gesture Sensor, a small breakout board with a built-in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. With this RGB and Gesture Sensor you will be able to control a computer, microcontroller, robot, and more with a simple swipe of your hand! This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price. RoboticsBD
The APDS-9960 is a serious little piece of hardware with built-in UV and IR blocking filters, four separate diodes sensitive to different directions, and an I2C compatible interface. For your convenience, we have broken out the following pins: VL (optional power to IR LED), GND (Ground), VCC (power to APDS-9960 sensor), SDA (I2C data), SCL (I2C clock), and INT (interrupt). Each APDS-9960 also has a detection range of 4 to 8 inches (10 to 20 cm) RoboticsBD
General Specification | |
Model | GY-APDS9960-3.3 |
Chip | APDS-9960 |
Input Supply Voltage (VDC) | 3.3 |
Communication Interface | I2C |
Length (mm) | 20 |
Width (mm) | 15.3 |
Height (mm) | 3 |
Weight (gm) | 0.8 |
Shipment Weight | 0.01 kg |
Shipment Dimensions | 6 × 9 × 1 cm |
1 x GY-9960LLC APDS-9960 RGB and Gesture Sensor Module
1 x 6 Pin Male Header
The latest price of GY-9960LLC APDS-9960 RGB and Gesture Sensor Module in Bangladesh is BDT 550 You can buy the GY-9960LLC APDS-9960 RGB and Gesture Sensor Module at best price from our RoboticsBD or visit RoboticsBD.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0009
54 Digital I/O terminals (14 of which have programmable PWM outputs). 16 Analog Inputs. 4 UARTs (hardware serial ports). 16 MHz crystal clock. RoboticsBD Operating voltage: 6 ~ 12v. Dimensions: 110 x 53 x 15 mm.
Reference: RBD-0032
Operating Voltage (logic level): 5V With Mini USB 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch.
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0428
Operational Voltage: 3.3V. Ambient Light & RGB Color Sensing. Proximity Sensing. Gesture Detection. Operating Range: 4-8in (10-20cm). I2C Interface (I2C Address: 0x39). RoboticsBD
Reference: RBD-1153
135 quality jumper Color: red, orange, yellow, green, blue, purple, gray, brown, white. Box size: 165 × 55 × 10 (LxWxH) mm. 140 pcs of 22 AWG solid wires
Reference: RBD-2206
Features Working Voltage: 3.3V or 5V Working Current: <1mA Operating Temperature Range: -10 ℃ ~ + 70 ℃ Interface Type: Analog Output Dimension (mm): 30 (L) x 23 (W) x 17 (H) Weight: 5g
Reference: RBD-1198
Industrial Systems Consumer Products Thermometers Thermally Sensitive Systems
Reference: RBD-1367
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver
Reference: RBD-0679
Sensitivity to Ammonia, Sulfide and Benzene steam Sensitive for benzene, alcohol, smoke Fast response and recovery Adjustable sensitivity. RoboticsBD Signal output indicator Output voltage boosts along with the concentration of the measured gases increases.
Reference: RBD-0441
Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust RoboticsBD
Reference: RBD-0424
Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0666
Crystal: the oscillation frequency of 455. Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000. Photo-detector and preamplifier in one package. Internal filter for PCM frequency. RoboticsBD Improved shielding against EMI. Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
Reference: RBD-2102
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing
Reference: RBD-1766
Supports 5V/3.3V input Onboard RT9161 faster load the appropriate speed Ideal for noisy power environment Application: DIY project.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-1751
Detection Gas: H2, Alcohol, CO, VOC Detection Range: 10~500ppmH2 5~500ppm Alcohol 10~500ppm CO Air Quality Sensor Module
Reference: RBD-1210
Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz
Reference: RBD-2095
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 °
Reference: RBD-0672
Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off). Current Consumption: 150mA. RoboticsBD DO output: 0.1 and 5V. AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V Detecting Concentration: 0.05-10mg/L Alcohol.
Reference: RBD-1202
3-axis magnetic electronic compass. Precise heading information. Operating Voltage: 3 -5 V DC. Driver Chip: HMC5883L. Communication: I2C protocol. Measuring range: ± 1.3-8 Gauss.
Reference: RBD-0797
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...
Reference: RBD-1931
Easy to Measure High Precision Low measurement cost Resolution up to 1mg/kg (mg/l)
Reference: RBD-2130
9DOF IMU Breakout9 can capture nine different types of motion or orientation of the 3-axis accelerometer to obtain the relevant data magnetic orientation and angular velocity that is three-axis gyroscope + triaxial accelerometer three-axis magnetic field +
Reference: RBD-2075
MQ-2 Smoke Gas Detector Sensor ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s
Reference: RBD-0678
Good sensitivity to CO/Combustible Gas High sensitivity to Methane, Propane, and CO Long life and low cost Simple drive circuit Input voltage: DC 5±0.2V Current Consumption: 150mA
Reference: RBD-1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-1856
Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load).. Double panel wiring solves crosstalk. Super mini design allows it to be easily placed in a variety of digital products. 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply. Filterless, Low Quiescent Current and Low EMI and Low Noise. Short Circuit Protection and Thermal...
Reference: RBD-419
Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...
Reference: RBD-2056
Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-1854
This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-1875
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-1188
5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-1006
No External Components Required Internal Thermal Overload Protection Internal Short Circuit Current Limiting Output Transistor Safe−Area Compensation
Reference: RBD-1157
Wick Width: 3 mm (+/- 2) Length: 1.5 Meter Material: Copper
Reference: RBD-0980
Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.