
Reference: 984
Heat Shrink Tube
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 245
Choose your desire Resistor value from below:
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
In the case of working with a MCU:
Reference: 1196
TSOP1738 - 38KHz IR receiver The SM0038 is an alternative to popular TSOP1738 IR receiver. Its a miniature receiver for Infrared remote control systems. PIN diode and pre-amplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated IR signal can be processed directly by microprocessor. Technical Datasheet (258.2...
Reference: 1172
এই লাইট হোল্ডার টি মানুষের উপস্থিতি পেলে লাইটটিকে অটোমেটিক চালু করে দিবে। Infrared Sensor Automatic Lighting Control Switch with lamp holder; convenient, safe & practical. Good solution for energy saving. You can conveniently let the light auto on/off. The switch can detect the human body's infrared, and use infrared to control the load. Easy...
Reference: 676
MQ-7 Carbon Monoxide Gas Sensor This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance.
Reference: 693
Infrared Line Track Tracker Follower Sensor
Reference: 689
LM75A IIC I2C High Accuracy Digital Temperature Sensor
Reference: 1188
IR Transmitter - White (5mm) 5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)
Reference: 1380
Sharp GP2Y0A02YK0F IR Range Sensor - 20 cm to 150 cm Infrared range finder 20cm (~8") to 150cm (~60")
Reference: 1352
GRID-EYE® INFRARED ARRAY SENSOR Panasonic Grid-EYE® is an 8x8 (64) pixel infrared array sensor. This sensor offers digital output (I2C) for thermal presence, direction, and temperature values. The built-in lens includes a 60-degree viewing angle. Grid-EYE features compact SMD design using MEMS thermopile technology. Applications for this sensor can...
Reference: 830
Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Screw Type
Reference: 555
Product Description 1. Current sensor chip: ACS712ELC-30A. 2. Pin 5V power supply, on-board power light. 3. The module can be measured plus or minus 30A current, Corresponding analog output of 66 mV / A. 4. No test current through, the output voltage is VCC / 2. 5. PCB size: 31 (mm) x13 (mm).
Reference: 813
Liquid Suspended Particles Turbidity Sensor Detection Module Kit
Reference: 1424
ZMCT103C AC current Sensor is the best for the purpose of the DIY project and industrial application, where we need to measure the accurate AC current with current transformer. This is an perfect choice to measure the AC current using Arduino/ESP8266/Raspberry Pi like an opensource platform. In many electrical projects, engineer directly deals with...
Reference: 574
The HMC5983 includes our state-of-the-art, high-resolution HMC118X series magnetoresistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I²C or SPI serial bus allows for easy interface.
Reference: 1174
DESCRIPTION Sensor module for measuring current. Both AC and DC, up to 5A can be measured. The output is a linear voltage between 0 – VCC, centered around VCC/2 at 0A. The load is connected in series to the screw terminal. * Dimensions: 31 x 13mm* Supply voltage: 5V* Sensitivity: 185mV/A* Sensor: ACS712ELC-05B
Reference: 396
Specification: Electrical parameters: JSN-SR04T Operating voltage: DC 5V Quiescent current: 5mA Total current work: 30mA Acoustic emission frequency: 40khz Farthest distance: 4.5m Blind: 25cm
Reference: 1177
This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...
Reference: 430
Compatible with Pololu QTR-8RC Library Max Distance from Ground: 3mm. Digital Line Follower Parameters: 1. Working voltage:5V2. 8-channel infrared detector / IR Reflectance Applications: 1. Robot2. Smart Car3. Laboratory4. DIY
Reference: 334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: 344
Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier.
Reference: 1200
Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes. The TSOP382 is a miniaturized receiver for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame while...
Reference: 663
Specification: The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. Features: Low power consumption Power supply for 2 ~ 5.5V DC
Reference: 1211
Features:The OPT101 is a monolithic photodiode with on-chip transimpedance amplifier.The ingrated combination of photodiode and transimpedance amplifier on a single chip eliminates the problems commonly encountered in discrete designs, such as leakage current errors, noise pick-up, and gain peaking as a result of stray capacitance.Output voltage increases...
Reference: 922
Slide Potentiometer 10K Linear Module Dual Output for Arduino
Reference: 152
SW-420 NC Type Vibration Sensor Module Arduino
Reference: 1249
This tiny, button-type, vibrating motor shakes with a vibration amplitude of 0.75g and draws approximately 60 mA when 3 V is applied to its leads. The shaftless design keeps this motor small Dimension: 10X3.0MM
Reference: 145
YL-69 Soil Hygrometer Humidity & Soil Moisture Detection Sensor For Arduino
Reference: 109
Gold Plated HDMI to VGA Converter for Raspberry Pi Color: White
Reference: 674
The MQ series of gas sensors use a small heater inside with an electrochemical sensor. They are sensitive to a range of gasses and are used indoors at room temperature. The output is an analog signal and can be read with an analog input of the Arduino.
Reference: 22
The HC-SR04 ultrasonic sensor uses sonar to determine the distance to an object like bats or dolphins do. It offers excellent range accuracy and stable readings in an easy-to-use package. It operation is not affected by sunlight or black material like Sharp rangefinders are (although acoustically soft materials like cloth can be difficult to detect)....
Reference: 694
ESP-12E/ ESP-12F CP2102 New Lolin NodeMcu Lua V3 Wireless Module Wifi Internet of Things (IoT) Development Board Based On ESP8266 Micro USB To TTL This is the famous NodeMCU which is based on ESP8266 WiFi SoC. This is version 3 and it is based on ESP-12E or ESP-12F (An ESP8266 based WiFi module). NodeMCU is also an open-source firmware and development...
Reference: 941
100% brand new and high quality JR male plug and JR Female plug, compatible each other Servo extension cable, 3 pin female to male connector For RC Car, plane and helicopter servo connection or receiver connection. Wire Length: 300mm
Reference: 439
This small size Bluetooth 4.0 TTL transceiver module allows your target device communicate with. your iPhone/iPAD, IOS 6 or Android 4.3 above devices. It's easy to use and completely encapsulated. You can set it as slave or master.You can use AT command set the baudrate.