Reference: RBD-1198

DS18B20 Digital Thermometer

Industrial Systems Consumer Products Thermometers Thermally Sensitive Systems

Reference: RBD-2071

SS49E Linear Hall Effect Sensor Module

Type: Magnetic Sensor Module Mainly Compatible with: Ardunio

Reference: RBD-2211

Soil Moisture Hygrometer Detection Humidity Sensor Module Corrosion Resistance Probe

Soil moisture sensor module Digital and analog output Adjustable threshold Waterproof and corrosion-resistant probe

Reference: RBD-0152

SW-420 NC Type Vibration Sensor Module

Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation

Reference: RBD-0813

Liquid Suspended Particles Turbidity Sensor Detection Module Kit

Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.

Reference: RBD-0104

6DOF Accelerometer Gyroscope GY-521 MPU-6050

Chip built-in 16bit AD converter, 16-bit data output Driver Chip: MPU6050 Operating Voltage: 3-5V DC Communication: I2C/IIC Protocol Gyro Range: ± 250, 500, 1000, 2000 °/s Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g

Reference: RBD-2792

Tilt Sensor AT407

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor...

Reference: RBD-0358

I2C Bi-Directional Logic Level Converter- 2 Channel

Dimensions: 11×15 x 2 (L x W x H) mm Weight: 1gm Mutual transform between 5V TTL and 3.3V TTL Two channels of logic and high voltage low voltage logic can two-way transform Portable and lightness, with 2 rows 4 pin contact pins

Reference: RBD-0427

Digital Tachometer Speed Module Sensor for Arduino UNO

Working voltage: 3.3V-5V Output form: digital output (0 and 1)

Reference: RBD-2748

Reset / Enable Controller - KA75330 3.3V Voltage Detector

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually, the battery runs down and goes below 3.3V, so the voltage to the ESP8266 core is too low, and could cause a lockup or corrupted data....

Reference: RBD-2474

TSAL620 Super-bright 5mm IR LED 940nm High Power Infrared Emitting Diode

Infrared LEDs are used for remote controls (they're the little LED in the part you point at your TV) and 'night-vision' cameras, and these little blue guys are high powered ones! They are 940nm wavelength, which is what nearly all devices listen to. They're 20 degree beamwidth, and work great for any kind of remote control application.

Reference: RBD-1196

TSOP1738 IR Infrared Receiver

Photo Detector, IR Filter, Preamplifier and PCM frequency filter in one package Shielding against EMI or RFI interference CMOS and TTL Compatible Active Low Output Immunity against ambient light Low Power Consumption Able to transfer data continuously up to 2400bps Supply Voltage : 4.5 – 5.5V

Reference: RBD-1644

TOF10120 Laser Range Sensor Module Distance Sensor

940nm laser classified as class 1 under operation condition by IEC 60825-1:2014-3rd edition Small ceramic package(20×13.2×2.0mm) Long range absolute range measurement up to 1.8m within 5% accuracy at indoor

Reference: RBD-2661

IR Beam Interruption Sensor - LED 3mm - 0-50 cm

The sensor reacts to an interruption in the beam of infrared light that is transmitted between the transmitter and receiver. When the beam is interrupted by another object, the receiver signals this event by lighting up. The module is equipped with a 3 mm IR LED with an illumination angle of 10°. Beam interruption systems are used e.g. in measuring gates.

Reference: RBD-2654

DHT11 Temperature And Humidity Sensor Module

The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.

Reference: RBD-1512

LDR 10-12 mm Light Depending Resistor

LDR 10 mm Light Depending Resistor Low-cost sensor device Wide spectral response Use in fire alarms, smoke alarms, control street light Low cost. Ambient Temperature Range. Wide spectral response.

Reference: RBD-2722

Person Sensor by Useful Sensors

Add computer vision capabilities to your project, without the coding! The Person Sensor includes a camera module pre-programed and connected over Qwiic... Person Sensor  V1.1 by Useful Sensors

Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBD-1737

USB Fingerprint Reader for Windows 10 Hello Biometric Scanner for PC

Fastest fingerprint identification in the world,  Support multi fingerprint  Instant match. 

Reference: RBD-1914

Reed Switch Module

Working voltage 3.3V-5 Output format: digital switching output (0 and 1)A fixed bolt holes for easy installation

Reference: RBD-2763

Optical Infrared Reflective Sensor Module

Uses infrared to detect a reflective line on the floor.

Reference: RBD-0675

MQ-6 LPG Gas Sensor

Model: MQ-6 Operating Voltage: 5V DC Detecting Range:200-10000 ppm Relative Humidity:<95% RH

Reference: RBD-2206

Analog Piezoelectric Ceramic Vibration Module

Analog piezoelectric ceramic vibration module Measures the extent of vibration Proportional to the strength of shock or vibration Interface type: Analog Output Dimensions: 30 (L) x 23 (W) x 17 (H) Weight: 5g

Reference: RBD-1210

OPT101P PHOTODIODE/AMPLIFIER

Single Supply:2.7-36V High Responsivity:0.45A/W(650nm) Bandwidth:14Khz

Reference: RBD-2102

DIP 3 Color RGB LED Module

RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing

Reference: RBD-2420

HW-488 Infrared Obstacle Avoidance IR Sensor Module

Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 °

Reference: RBD-0663

TTP223B Digital Touch Sensor Capacitive Touch

Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD

Reference: RBD-0150

5mW Adjustable Laser Dot Diode Module

Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~＋40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-2745

LSM9DS1 9DOF Accel/Mag/Gyro/Temp Sensor Module

The LSM9DS1 is a versatile, motion-sensing system-in-a-chip. It houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer – nine degrees of freedom (9DOF) in a single IC! The LSM9DS1 is equipped with a digital interface, but even that is flexible: it supports both I2C and SPI, so you’ll be hard-pressed to find a microcontroller it doesn’t...