Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-2099
Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins
Reference: RBD-0665
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity. RoboticsBD Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-0679
Sensitivity to Ammonia, Sulfide and Benzene steam Sensitive for benzene, alcohol, smoke Fast response and recovery Adjustable sensitivity. RoboticsBD Signal output indicator Output voltage boosts along with the concentration of the measured gases increases.
Reference: RBD-1932
Rated voltage: 5 VDC. Port: Digital quantity. Fixed hole:3mm. Pitch:15mm. Drive: MOS tube high-level trigger, low-level cutoff. Compatible with UNO R3/ Mega2560.
Reference: RBD-2303
LED peak wavelength: 660nm/880nm LED power supply voltage: 3.3~5V Detection signal type: light reflection signal (PPG) Output signal interface: I2C interface
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-0812
Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.
Reference: RBD-2078
No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA
Reference: RBD-2451
Pulse Sensor 3.3-5V Heartbeat Heart Rate Monitor Sensor Easy to use finger-tip heart rate detector module with built-in noise filter and signal amplification.
Reference: RBD-0241
Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical LM35 (working) tested by...
Reference: RBD-0958
Five Operating Modes Integrated MCU Onboard Processing Standard I2C Digital Interface Optimized Low-Power Modes Optional NTC Thermistor Pins
Reference: RBD-2088
Operating Voltage: 5v DC. This module is Small and Simple to use. Digital switch output (0 & 1) High sensitivity Completes the circuit when the module is tilted LED lights up when tilt switch is activated
Reference: RBD-2452
This Pulse Sensor is a heart rate sensor designed for Arduino microcontrollers. Development professionals use. The Pulse Sensor Kit brings you all the experience you need, a complete package. The kit includes: A 24inch 3p DuPont line, A soft Velcro Finger Strap, A sensor size sensor ear clip, 4 Velcro dots, and 9 transparent protective dot Pulse Sensor is...
Reference: RBD-0689
Operating Voltage: 2.8 V to 5.5 V Accuracy: ± 1.5°C Zero power resistance: 100 KΩ Operating temperature range: -55 ~ +125 ℃
Reference: RBD-1377
Module Name:CJMCU-4541 Sensor: MICS-4514 Type: Carbon Monoxide Nitrogen Oxygen Sensor
Reference: RBD-2089
Consists of a mercury switch 680Ω resistor LED that will light up when tilt is detected.
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-1640
Color: White Material: Metal + Plastic Operating Voltage : 12V DC Standby Current : ≤90mA Alarm Current : ≤100mA
Reference: RBD-0830
Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree. Screw Type
Reference: RBD-1654
5 In 1 Portable CO2 Detector Air Quality Detector Intelligent Air Detector Temperature and Humidity Sensor Carbon Dioxide Monitor TVOC Formaldehyde Detection HCHO Detector Color Black
Reference: RBD-2206
Analog piezoelectric ceramic vibration module Measures the extent of vibration Proportional to the strength of shock or vibration Interface type: Analog Output Dimensions: 30 (L) x 23 (W) x 17 (H) Weight: 5g
Reference: RBD-0923
Measuring range: temperature -40-80 ℃; humidity 0; 99.9%RH Measurement accuracy (25℃): temperature: + 0.5; humidity: + 2%RH (10; 90%RH) Resolution: temperature: 0.1 ℃, humidity: 0.1%RH Attenuation value: temperature: <1℃ / year; humidity: < 1%RH/ years High precision Capacitive type Full range temperature compensated Relative humidity and...
Reference: RBD-1716
Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L<0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi.
Reference: RBD-2229
Highly sensitive and reliable Piezoelectric Vibration Sensor Module Detects vibration and measures acceleration Analog and digital outputs Suitable for industrial control systems, robotics, automotive, and consumer electronics
Reference: RBD-1042
Operating Voltage: 3.3 ~ 5.5 VDC. Operating Current: 5mA. Interface: PH2.54-3P. Dimensions mm(LxWxH): 98 x 23 x 4. Supports 3-Pin Gravity Sensor interface Analog output. Weight (gm): 15.
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December
Reference: RBD-2235
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Operating Temperature: -20~70 Clear sound Ultra-thin and lightweight Low power consumption for voltage type
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-1751
Detection Gas: H2, Alcohol, CO, VOC Detection Range: 10~500ppmH2 5~500ppm Alcohol 10~500ppm CO Air Quality Sensor Module
Reference: RBD-2236
Plate Diameter: 20mm Element Diameter: 14mm Plate Thickness: .42mm Lead Length: ~50mm Plate Material: Brass Resonant Frequency (kHz): 6.3 +/- .6kHz