Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1640
Color: White Material: Metal + Plastic Operating Voltage : 12V DC Standby Current : ≤90mA Alarm Current : ≤100mA
Reference: RBD-0797
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...
Reference: RBD-1654
5 In 1 Portable CO2 Detector Air Quality Detector Intelligent Air Detector Temperature and Humidity Sensor Carbon Dioxide Monitor TVOC Formaldehyde Detection HCHO Detector Color Black
Reference: RBD-1716
Working Voltage: 5.0V Maximum Working Current: 100mA Data Interface Level: L<0.8V, H>2.7V, maximum voltage level 3.3V Particle Measurement Range: 0.3 ~ 1.0μm; 1.0 ~ 2.5μm; 2.5 ~ 10μm Note: Please purchase this adapter board to use it with Arduino and Raspberry Pi.
Reference: RBD-1202
3-axis magnetic electronic compass. Precise heading information. Operating Voltage: 3 -5 V DC. Driver Chip: HMC5883L / QMC5883L Communication: I2C protocol. Measuring range: ± 1.3-8 Gauss.Library: https://github.com/keepworking/Mecha_QMC5883Lhttps://www.arduino.cc/reference/en/libraries/qmc5883lcompass/
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-1751
Detection Gas: H2, Alcohol, CO, VOC Detection Range: 10~500ppmH2 5~500ppm Alcohol 10~500ppm CO Air Quality Sensor Module
Reference: RBD-1757
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity: X: 28.6 LSB/g. Y: 31.2 LSB/g. Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection.
Reference: RBD-1934
Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics
Reference: RBD-1766
Supports 5V/3.3V input Onboard RT9161 faster load the appropriate speed Ideal for noisy power environment Application: DIY project.
Reference: RBD-1966
Tuya Smart Wifi Wireless Natural Gas Leak Detector Gas Sensor Household Combustible LPG Gas Leak Alarm Detector With LCD Display
Reference: RBD-1811
AS5600 Magnetic Induction Angle Measurement Sensor
Reference: RBD-2075
MQ-2 Smoke Gas Detector Sensor ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s
Reference: RBD-1813
ICM-20948 MEMS Motion Tracking Device Sensor Board 9 Axis
Reference: RBD-2325
Brand: DFRobot
This is a dissolved oxygen sensor kit. A dissolved oxygen meter is used to measure the dissolved oxygen in water, to reflect the water quality. It is widely applied in many water quality applications, such as aquaculture, environment monitoring, natural science, etc. There’s an old saying regarding keeping fish, “Good fish deserves good water”. Good...
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-2497
Compact size, measuring only 13*13*2.5mm Low power consumption High sensitivity and rapid response recovery Advanced MEMS technology Gas detected: CO Sensitivity: R0(in air) / Rs(in 150ppm CO) ≥ 3 Lifespan: ≥5 years (in air)
Reference: RBD-1913
Onboard LDO Voltage regulator Can be interfaced with 3V3 or 5V Microcontroller. Tap/Double Tap Detection Free-Fall Detection Analog output Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from the motor and other high current electronics Power LED
Reference: RBD-2508
The ENS160 is a digital multi-gas sensor specifically designed for indoor air quality testing that optimizes the detection of a wide variety of gases and volatile organic compounds (VOCS), including toluene, hydrogen, ethanol, N02 and ozone. The air quality sensor is used in home and building automation, consumer products, electrical and air purification
Reference: RBD-1919
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-2667
MG811 (CO2) Carbon Dioxide Gas Sensor Metal Oxide Sensor Highly sensitive to CO2 Less sensitive to alcohol and CO Analog and digital output options Compatible with Arduino & Raspberry Pi Wide detecting scope
Reference: RBD-2130
9DOF IMU module with compass, acceleration, and gyroscope sensors Captures nine different types of motion or orientation Measures 3-axis gyroscope, triaxial accelerometer, and triaxial magnetic field Power supply: 3-5V (internal low dropout regulator)
Reference: RBD-2729
The SGP41 from Sensirion is an innovative VOC and NOx sensor engineered to serve as a digital smart switch and regulation unit in air treatment systems like air purifiers. Utilizing Sensirion's advanced Gas Index Algorithm, the sensor accurately processes two distinct signals, enabling automatic triggering of air treatment devices for the removal of...
Reference: RBD-2329
The LSM6DS3TR-C is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope performing at 0.90 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience for the consumer.
Reference: RBD-2730
The SGP40 is a digital gas sensor designed for easy integration into air purifiers or demand-controlled ventilation systems. Sensirion’s CMOSens® technology offers a complete, easy-to-use sensor system on a single chip featuring a digital I2C interface and a temperature-controlled micro hotplate, providing a humiditycompensated VOC based indoor air...
Reference: RBD-2448
This module serves to breakout the MMA8452Q chipset, a chip capable of providing 3 axis acceleration readings. The chipset features a 3 axis accelerometer (±2-8g) and an internal dropout regulator to allow the use of 5V and 3.3V supplies. When combined with free libraries it is possible to utilize the chipset's processing power to perform data conversions...
Reference: RBD-2793
Cost-Effective Oxygen Detection Dual Detection Reliable Performance Versatile Outputs Compact & Easy to Use *Not a medical device*
Reference: RBD-2733
GY-50 L3G4200D 3-Axis Gyroscope Sensor Module Three selectable full scales (250/500/2000 dps) I2C and SPI digital output interface avail. Two I2C address you can select by jumpers 16 bit-rate value data output 8-bit temperature data output Wide supply voltage: 2.4 V to 3.6 V Low voltage-compatible IO (1.8 V) Embedded power-down and sleep...
Reference: RBD-2794
All-in-one Oxygen Monitoring: This complete kit combines the OCS-3F ultrasonic sensor with an LCD display and power supply for convenient oxygen concentration and flow rate monitoring. Enhanced User Experience: The large LCD screen displays real-time oxygen concentration (21% - 95.6%), flow rate (up to 20 L/min), and room temperature for clear and easy...
Reference: RBD-2743
Wide supply voltage 1.71 V to 3.6 V Independent IO power (1.8V) and power supply voltage compatible Ultra-low power consumption of ± 2g / ± 4G / ± 6g / ± 8G / ± 16g IIC / SPI digital output interface 16-bit data output Programmable Embedded State Machine Embedded temperature sensor Embedded self-test Embedded FIFO 10,000 g high impact resistance
Reference: RBD-2835
The sensor has high sensitivity to gases such as methane, propane, butane and hydrogen. The supply voltage is 24 V. Measuring range is up to 10,000 ppm.