Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V
Reference: RBD-2099
Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins
Reference: RBD-0700
Operating Voltage: 3.3V-5.5V Low Power Consumption High Accuracy Small Size
Reference: RBD-1424
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-2215
Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.
Reference: RBD-2303
LED peak wavelength: 660nm/880nm LED power supply voltage: 3.3~5V Detection signal type: light reflection signal (PPG) Output signal interface: I2C interface
Reference: RBD-0797
5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...
Reference: RBD-1675
Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0
Reference: RBD-2310
1. Reliable Use: With infrared distance detection sensor and touch detection sensor, the robot you designed can adapt to more situation.2. Line Sensing: Has 6 way high sensitivity infrared sensors, 5 way patrol lines and 1 way for road barrier, which can easily identify and track complex and intersecting black and white lines. Output low level for black...
Reference: RBD-2451
Pulse Sensor 3.3-5V Heartbeat Heart Rate Monitor Sensor Easy to use finger-tip heart rate detector module with built-in noise filter and signal amplification.
Reference: RBD-0812
Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.
Reference: RBD-1835
Input current (RMS): 50A. Work temperature: -25℃~+70℃. Storage temperature: -30℃~+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.
Reference: RBD-2414
This tracking module adopts four tracking probes, and optimized spacing layout. The inner two probes can accurately identify the black line. The outer two probes can assist the inner probe to identify the black line and provide early warning. The car can recognize the 90°curved road and other difficult tracks. Knob-type adjustable resistors plus...
Reference: RBD-2452
This Pulse Sensor is a heart rate sensor designed for Arduino microcontrollers. Development professionals use. The Pulse Sensor Kit brings you all the experience you need, a complete package. The kit includes: A 24inch 3p DuPont line, A soft Velcro Finger Strap, A sensor size sensor ear clip, 4 Velcro dots, and 9 transparent protective dot Pulse Sensor is...
Reference: RBD-0816
Power Supply Voltage: 3.3V~5V Operating Current: <5mA Measuring Distance: 5-100mm VCSEL light source Strong anti-interference Based on DFrobot Fermion VL6180X ToF Distance Ranging Sensor (Breakout)
Reference: RBD-1836
Input Current : 0-30A Output Mode: 0-1V @ 30mA Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection Meet UL94-V0 flame retardant properties
Reference: RBD-2533
This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate analog voltage output.Note:...
Reference: RBD-0822
S49E hall sensor Features wide-range voltage comparator LM393 Signal output indicator Analog / Digital output
Reference: RBD-1972
Brand: DFRobot
Brand Gravity Analog AC Current Sensor 20A AC Current Signal Conversion Module Open Type AC Transformer Probe Included Non-contact Measurement
Reference: RBD-2598
Brand: RoboticsBD
Precise Line Following: Navigate black lines on white surfaces with 8 high-resolution sensors. Easy Microcontroller Integration: Connect directly to your microcontroller with digital outputs. Fast and Responsive: Achieve accurate line following even at high speeds. Simple Calibration: Calibrate sensors quickly and easily with a large knob. Versatility:...
Reference: RBD-1062
Temperature detection of the two-dimensional area: 8 × 8 (64 pixels). Digital output (capability of temperature value output). Compact SMD package (adaptively to reflow mounting). RoHS compliant.
Reference: RBD-2071
Type: Magnetic Sensor Module Mainly Compatible with: Ardunio
Reference: RBD-2611
This sensor module has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate digital I/O-measurable output.
Reference: RBD-1066
Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.The Mini Metal Detector Module arrives disassembled, requiring assembly using a soldering iron and soldering accessories. Moderate knowledge of soldering and...
Reference: RBD-2072
Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light
Reference: RBD-2763
Uses infrared to detect a reflective line on the floor.
Reference: RBD-1192
Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.
Reference: RBD-2073
Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.
Reference: RBD-2836
Operating Voltage: 3.5V-5V Supply Current: 15mA Optimal Sensing Distance: 3mm Designed with the reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn)
Reference: RBD-1194
Product Name : Optical Sensor Switch Model : RPR220 Color : Black Net Weigh : 3g Material : Plastic, Metal Detection Distance:1-13mm Working Voltage:DC 30V(Max) Output Type:Photo Transistor
Reference: RBD-2120
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.
Reference: RBD-1199
Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance