Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-2451
Pulse Sensor 3.3-5V Heartbeat Heart Rate Monitor Sensor Easy to use finger-tip heart rate detector module with built-in noise filter and signal amplification.
Reference: RBD-1644
940nm laser classified as class 1 under operation condition by IEC 60825-1:2014-3rd edition Small ceramic package(20×13.2×2.0mm) Long range absolute range measurement up to 1.8m within 5% accuracy at indoor
Reference: RBD-2452
This Pulse Sensor is a heart rate sensor designed for Arduino microcontrollers. Development professionals use. The Pulse Sensor Kit brings you all the experience you need, a complete package. The kit includes: A 24inch 3p DuPont line, A soft Velcro Finger Strap, A sensor size sensor ear clip, 4 Velcro dots, and 9 transparent protective dot Pulse Sensor is...
Reference: RBD-1645
Voltage operation: 2.7V-5V Measuring distance: 4 to 50 cm Output: Digital (I/C) / Analog Output Sensor: Infrared LED and CMOS image sensor
Reference: RBD-2474
Infrared LEDs are used for remote controls (they're the little LED in the part you point at your TV) and 'night-vision' cameras, and these little blue guys are high powered ones! They are 940nm wavelength, which is what nearly all devices listen to. They're 20 degree beamwidth, and work great for any kind of remote control application.
Reference: RBD-1677
Contact Rating: 10 W. Switching Voltage: 220 V. Switching Current: 0.5 A. Breakdown Voltage: 220 VDC. Carry Current: 1 A. Contact Resistance: 100 mΩ.
Reference: RBD-2203
The Mini RGB Bluetooth Controller is a small device that allows you to control the color and brightness of RGB LED strips via Bluetooth. It can work with DC voltage of 5V, 12V, and 24V and has a music sync feature that allows the lights to change color and brightness in sync with music. It can be used in a variety of settings such as home lighting,...
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-2558
This is a mini Laser light module with onboard triode current amplifier circuit, it gets only 1.3mA from the SIG pin so it is compatible with much more MCU. Note: For safe use, the module must not directly illuminate human eyes or irradiate human body for a long time. Features: - Output wavelength: 650nm - Working voltage: 4.75-5.5V - Working current:...
Reference: RBD-1858
CDD-11P PNP Output Photoelectric sensor Epoxy filled housing ensures resistance to vibration Rigid Nickel Plated Brass housing This is PNP Output CDD-11P. For NPN Output CDD-11N please check here.
Reference: RBD-2661
The sensor reacts to an interruption in the beam of infrared light that is transmitted between the transmitter and receiver. When the beam is interrupted by another object, the receiver signals this event by lighting up. The module is equipped with a 3 mm IR LED with an illumination angle of 10°. Beam interruption systems are used e.g. in measuring gates.
Reference: RBD-1859
CDD-11N NPN Output Photoelectric sensor Epoxy filled housing ensures resistance to vibration Rigid Nickel Plated Brass housing This is NPN Output CDD-11N. For PNP Output CDD-11P please check here
Reference: RBD-2715
Visible light to analog voltage converter for measuring the intensity of visible light. Visible light sensitivity with peak at 570nm +/- 60 degree angle of sensitivity Fast reacting in uSec range. Analog voltage output proportional to the intensity of light falling on the detector 3.3 and 5V compatible
Reference: RBD-1942
Actuation Distance : 15 – 25 mm; Connecting cable length: 30 cm. Magnetic sensor alarm, control the switch of the circuit via the built-in magnet Alarm when someone intrudes into your places Can be used in places like apartment, hotel, office, etc.
Reference: RBD-2763
Uses infrared to detect a reflective line on the floor.
Reference: RBD-2009
Digital Auto Counter Meter with Hall Effect Proximity Switch Sensor (Battery Powered) No Power Required Digital Counter Meter Battery Attached Hall Effect Proximity Switch Sensor Connect Hall Effect Proximity Switch Sensor 2 wire to counter terminals 1&2. If the sensor detects a magnet it will start to count.
Reference: RBD-2836
Operating Voltage: 3.5V-5V Supply Current: 15mA Optimal Sensing Distance: 3mm Designed with the reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn)
Reference: RBD-2842
The QRE1113 breakout board offers a digital output solution, utilizing a capacitor discharge circuit to assess reflection levels. This compact board is designed for line sensing applications, particularly suitable when only digital I/O pins are available in the system. It is compatible with both 3.3V and 5V systems, providing versatility in various...
Reference: RBD-2148
Non-contact detection Suitable for liquids of various densities and forms Easy installation for all kinds of detection occasions Compatible with containers of various materials and thicknesses Reliable performance with anti-interference ability
Reference: RBD-2888
A sensor that allows you to measure your pulse with your finger using a phototransistor. The red LED lights up each time it detects a pulse. Powered by 5 V.
Reference: RBD-2169
US1000-21A ultrasonic flow sensor ultrasonic heat meter sensor Underwater Sensor high-frequency ultrasonic sensor Model: US1000-21A High frequency type ultrasonic underwater sensor Transceiver category Nominal frequency: 1.0MHz ± 5% Bandwidth: 200.0KHz
Reference: RBD-2183
Digital auto counter meter with infrared proximity sensor 24V power supply Adjustable sensing range from 3 to 80 cm Easy to mount chassis Diffuse reflective type light source DC 3-wire NPN-NO output Sensory distance regulator and output LED indicator
Reference: RBD-2215
Working voltage (V): 3.3 ~ 5 Working current (A): Above 1A Operating Temperature (℃): -10 ~ +50 Mounting hole: M3 Detection range: 1mm ~ 60 cm adjustable.
Reference: RBD-2231
Working voltage:2.8-3.8V ALS, IR LED and Proximity Detector in an Optical Module; Ambient Light Sensing (ALS); Approximates Human Eye Response; Programmable Interrupt Function with Upper and Lower Threshold; Up to 16-Bit Resolution; High Sensitivity Operates Behind Darkened Glass; Low Lux Performance at 0.01 lux;
Reference: RBD-2247
Onboard STM8S103 high-performance microprocessor With digital tube display Valid Measurement Distance: 3-400cm Display Unit: cm Maximum Input Voltage: 5VDC 2.54mm White Socket: 5V power interface.
Reference: RBD-2310
1. Reliable Use: With infrared distance detection sensor and touch detection sensor, the robot you designed can adapt to more situation.2. Line Sensing: Has 6 way high sensitivity infrared sensors, 5 way patrol lines and 1 way for road barrier, which can easily identify and track complex and intersecting black and white lines. Output low level for black...
Reference: RBD-2313
Sensing range: 3 – 80cm. Input voltage: 5VDC. Current Consumption: 300mA. Digital Output. Cable length: 1m. Diffuse reflective type.
Reference: RBD-2420
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 °
Reference: RBD-2443
The Collision Switch Module is used to detect a collision with an object or to detect the limit of travel.
Reference: RBD-2444
Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.