Reference: RBD-0338

Brand: Waveshare

Dust Sensor For Arduino

Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm  Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F

Reference: RBd-2402

60GHz mmWave Multi Human Sensing Radar Module Sensor

The 60GHz mmWave Multi-Human Sensing Radar Module Sensor can detect up to 8 people in its sensing area. The software is in Chinese, and it can report the position of people using a serial terminal.

Reference: RBD-0428

APDS-9930 RGB and Gesture Sensor

Operational Voltage: 3.3V. Ambient Light & RGB Color Sensing. Proximity Sensing. Gesture Detection. Operating Range: 4-8in (10-20cm). I2C Interface (I2C Address: 0x39). RoboticsBD

Reference: RBD-0382

GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module

3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD

Reference: RBD-0417

Force Sensitive Resistor - Square

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD

Reference: RBD-2324

Brand: DFRobot

Gravity Analog ORP Sensor Meter for Arduino

In the ever-increasing need and awareness for health and safety, water has become a focus point for proper disinfection treatment as aftereffects of industrialization can become a danger for contamination of water via direct contact. Water is a critical control point of contact where proper treatment can greatly reduce these microbes, thereby reducing the...

Reference: RBD-0152

SW-420 NC Type Vibration Sensor Module Arduino

Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation

Reference: RBD-0147

HR202 Humidity Detection Sensor Module

Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).

Reference: RBD-1738

Active Speaker Buzzer Module for Arduino 5V

Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH):  26 x 15 x 11 mm

Reference: RBD-0823

Optical Sensitive Resistance Light Detection Photosensitive LDR Sensor Module

LDR module 4 PIN Operating voltage 3.3V-5V Signal output indicator light. LDR module 4 PIN Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)

Reference: RBD-2102

DIP 3 Color RGB LED Module

RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing

Reference: RBD-2100

Flame Sensor Module

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-2347

TSL2591 High Dynamic Range Digital Light Sensor

TSL2591 Digital Light Sensor Breakout Module High Dynamic Range Lux IR Infrared Full Spectrum Diodes Detect 3.3V for Arduino

Reference: RBD-0995

LDR 5 mm Light Depending Resistor

Diameter: 5mm No. of Pins: 2 Type of Mounting: PCB Through Hole Maximum Operating Temperature: +800°C (Approx.) Dark resistance:1-20 Mohm

Reference: RBD-2099

Touch Sensor Switch Module

Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins

Reference: RBD-1974

Brand: DFRobot

Gravity Huskylens AI Camera Vision Sensor with Silicone Case

One-click learn Machine Learning Enabled Onboard Screen Extreme Performance

Reference: RBD-0687

BMP280 Pressure Sensor Module

Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V. Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C). Peak current: 1.12mA. RoboticsBD Operating Pressure: 300 hPa to 1100 hPa. Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.

Reference: RBD-0664

ADXL345 Triple Axis Accelerometer Breakout

Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD

Reference: RBD-1405

Turbidity Sensor Suspended Turbidity Value Detection Module Kit

Working voltage: 5.00V DC Working current: 40mA (MAX) Response time: <500ms Insulation resistance: 100MΩ (Min) Analogue output: 0~4.5V; Digital output: high/low-level signal (the corresponding threshold can be selected by adjusting the potentiometer) Operating temperature: -20℃~90℃

Reference: RBD-2444

Optical Endstop Switch with 1m Cable

Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.

Reference: RBD-2211

Soil Moisture Hygrometer Detection Humidity Sensor Module Corrosion Resistance Probe

Soil moisture sensor module Digital and analog output Adjustable threshold Waterproof and corrosion-resistant probe

Reference: RBD-2103

IR Remote Control without Battery

Remote control distance: more than 8 meters Crystal: the oscillation frequency of 455 IR carrier frequency: 38KHz Output form: Digital Power Supply: CR2032 Battery Pointing Angle: up to 60º Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000 click

Reference: RBD-1211

CJMCU-101 OPT101 Analog Light Sensor Intensity Module

Single supply: 2.7-36v Size of photodiode: 2.29mm x 2.29mm Internal feedback resistor: 1MΩ

Reference: RBD-0424

Si7021 Industrial High Precision Humidity Sensor I2C Interface for Arduino

SI7021 SHT21 HTV21 Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface

Reference: RBD-2144

HC-SR505 Mini Infrared PIR Motion Sensor

Automatic induction: to enter the sensing range Ultra-small size. Repeatable trigger Wide operating voltage range Micropower: quiescent current <50 Output high signal: easy docking and all kinds of circuits.

Reference: RBD-2443

Collision Switch Module

The Collision Switch Module is used to detect a collision with an object or to detect the limit of travel.

Reference: RBD-0396

Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD

Reference: RBD-2445

HY-SRF05 Ultrasonic Range Finder Module

Uses ultrasonic sound waves to detect obstacles and measure distance

Reference: RBD-0391

AD8232 ECG Measurement Module Kit

Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD

Reference: RBD-2146

Galvanic Skin Response GSR Sensor

Operating voltage:3.3V/5V Sensitivity: Adjustable via a potentiometer Input Signal: Resistance, NOT Conductivity Output Signal: Voltage, analog reading Finger contact material:  Nickel