5 mm Green LED (Pack of 5)

Sonoff 4CH R2 Smart Switch Wifi

Sonoff 4CH R2 Smart Switch Wifi Power Supply: 90V~250V AC(50/60Hz) Max. Current: 10A/gang Max. Power：2200W/gang, 2200W/Total Wireless Standard: 802.11 b/g/n Security Mechanism: WPA-PSK/WPA2-PSK Enclosure Material: Fire-retardant ABS V0

Precision Real Time Clock Module DS3231 AT24C32 I2C

Precision Real Time Clock Module DS3231 AT24C32 I2C

TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino

The TTP229 is capacitive sensing design specifically for touch pad controls. The device has a built in regulator for the touch sensor. Stable sensing method can cover diversity conditions. Interface control panel links through non-conductive dielectric material. The main application is focused at replacing of the mechanical switch or button.

Reference: SparkFun

Flex Sensor 2.2"

Description: A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!

IR receiver Diode

10K Ohm Potentiometer

2N2222 NPN Transistor

Mini Cooling Fan 40x40x10mm

LF356n Operational Amplifiers

Brand: SparkFun Electronics

Camera Module - pcDuino V3 (2MP)

14500 Rechargeable Lithium Battery 1300mah 3.7v

14500 Rechargeable Lithium Battery 900mah 3.7v  Buy Battery Holder 2S  3S  (Compatible with AA Battery Holder) Model: 14500Type: Li-Ion BatteryMark Capacity: 1300mahNominal Voltage: 3.7vColor:    Blue   Weight: 17gRechargeable Battery: YesRechargeable Times: Up to 500 timesSize: 50mm x 14mm (Diameter)Place of Origin: China (Mainland)

AA Battery Holder 3S

IR Infrared Remote Decoder Encoding Transmitter & Receiver Wireless Module

X9C103S Digital Potentiometer Module for Arduino

Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S

Slip Ring - 6 Wire (1.5A) max 240V

Features: 6 wires Voltage: 210VDC / 240VAC Current Rating: 1.5A Operating Speed: 250RPM Compatible with data bus protocols Transfers analog and digital signals

New ENC28J60 Ethernet LAN Network Module For Arduino

Chip board ENC28J60-I/SOThe board 25MHZ crystalThe network interface board HR911105A3.3 V power supply pinThe board size : 56 (mm) x 34 (mm)

Obstacle Avoiding Robot Kit

DC-DC Boost Module

XL6009 DC-DC Booster

18650 Li-ion Rechargeable Battery

18650 Li-ion Rechargeable Battery 3.7 Volt Rechargeable Lithium ION Re/Discharging Protection Circuit   It's a clone battery so the ampere couldn't be guaranteed.

12V 60W TEC1-12706 Thermoelectric Cooler Peltier

Get cold or heat up by simply reversing the polarity, used for numerous applications from CPU coolers to alternate power sources, or even for your own custom car drink warmer/cooler.

Solenoid - 5v (small)

Description: Solenoids are a great way to induce linear motion  for pushing, pulling or controlling switches and levers.This smaller  solenoid is designed to work directly with 5V~6V which makes it a  great match for embedded projects. It has a throw of about 4.5mm  and 2 M2 mounting holes on the body.

DS1302 Real Time Clock Module (DS1302Z clock chip,32.768KHZ crystal)

Weighing Sensor 24 Bit HX711 Dual-Channel

Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. 

Brand: DFRobot

APC220 Radio Communication Module

INTRODUCTION The APC220 radio module provides a  simple and economic solution to wireless data communications. Integrates an  embedded high speed microprocessor  and high performance IC that creates a  transparent UART/TTL interface, and  elminates any

Heart Rate Pulse Sensor Pulsesensor Sensor Module For Arduino

Description: Heart rate data can be really useful whether you’re designing an exercise routine, studying your activity or anxiety levels or just want your shirt to blink with your heart beat. The problem is that heart rate can be difficult to measure. Luckily, the Pulse Sensor Amped can solve that problem!

Songle Power 12VDC Relay SRU-12VDC-SL-C PCB 5 Pin

• Switching capacity available by 10A in spite of small size design for highdensity P.C. board mounting technique. • UL,CUL,TUV recognized. • Selection of plastic material for high temperature and better chemical solution performance. • Sealed types available. • Simple relay magnetic circuit to meet low cost of mass production.

Light Depending Resistor (LDR)

CD4026BE

TP4056 5V Mini USB Charger Module

Brand: Waveshare

Logic Level Converter