- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
5 mm Yellow LED (Pack of 5)
Store Pickup Available!
Free Ship Over 5000 BDT
LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.
This is a very basic 5mm LED with a Yellow lens. It has a typical forward voltage of 2.0V and a rated forward current of 15mA.
This is a very compact DC-DC step-down converter capable of supplying any voltage between 1.23 and 30 V from a higher voltage power supply (up to 35 V).
PL2303 USB to TTL Converter Windows 7 & 10 Compatible
ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is an highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module.
DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator Input voltage: DC 3 V to 6 VInput current: 2 A - 5 AHigh-pressure type: the type of pulse currentOutput voltage: 400000 v(Please pay attention to safety)High-pressure discharge distance between 10 mm - 20 mmThe output high voltage wire length: 100 mm
Digispark USB Development Board The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when...
IR Transmitter - White (5mm) 5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)
Description: Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V~6V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body.
Description: This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on the other end with a mating socket. Compatible With: Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL...
The TTP229 is capacitive sensing design specifically for touch pad controls. The device has a built in regulator for the touch sensor. Stable sensing method can cover diversity conditions. Interface control panel links through non-conductive dielectric material. The main application is focused at replacing of the mechanical switch or button.
Description: This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board...
3S 11.1V 12.6V 25A W/Balance 18650 Li-ion Lithium Battery PCB Protection Board Specification: Brand newSize: about 56mm*45mm*1.2mmOver voltage range: 4.25-4.35v±0.05vOver discharge voltage range: 2.3-3.0v±0.05vMaximum operating current: 0-25AMaximum transient current: 34-40AQuiescent current: less than 30uA
Iduino Yun Shield Compatible with Arduino Leonardo, Uno, Duemilanove, Diecimila and Mega Arduino 3G+Wifi+Ethernet Shield Robotics Bangladesh 3g+ Wifi+ Ethernet + USB+ Openwrt (Linux) Geeetech Latest Iduino Yun Shield board Linux WiFi 3G Ethernet USB for Arduino http://www.geeetech.com/wiki/index.php/Iduino_Yun_Shield
Product Name : DC Solenoid Electromagnet;Model : JF-0530B;Rated Voltage : DC 12V RatedCurrent : 300mA;Action Form : Pull Push Type;Rated Stroke & Force : 10mm, 5N Body Size : 30 x 15x 15mm/1.2"x 0.59"x 0.59"(L*W*H);Pluger Dia. : 56mm/ 2.2" Cable Length : 20cm/ 7.9";Material : Metal, Electronic Parts Weight : 32g;Package Content : 1 x DC Solenoid...
Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier.
Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...