- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- Power Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- Retired Products
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
White Led 5mm(pack of 5)
Store Pickup Available!
Free Ship Over 5000 BDT
Specification: Input voltage range：4～38VDC(Note:input voltage not exceeding 38V) Output voltage range：1.25-36VDC adjustable Output current: 0-5A, recommended for use in 4.5A. Output power: 75W Working temperature: -40~+85 degrees Operating frequency: 180KHz Efficiency:96%（max) Short circuit protection: yes(limit current 8A).
• Switching capacity available by 10A in spite of small size design for highdensity P.C. board mounting technique. • UL,CUL,TUV recognized. • Selection of plastic material for high temperature and better chemical solution performance. • Sealed types available. • Simple relay magnetic circuit to meet low cost of mass production.
Description: This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board...
Precision Real Time Clock Module DS3231 AT24C32 I2C
The Keweisi KWS-10VA is great for checking 5V USB loads. We use one of these devices with an Original iPad charger for testing general charging issues There are two ports on the device, however they are connected together, so we don’t suggest charging multiple devices at once. For convenience however, you can connect a Micro USB, and Lightning cable (for...
Description:Model: STM32F103C8T6.Core: ARM 32 Cortex-M3 CPU.Debug mode: SWD.72MHz work frequency.64K flash memory, 20K SRAM.2.0-3.6V power, I/O.Reset(POR/PDR).4-16MHz crystal.On-board Mini USB interface, you can give the board power supply and USB communication.
Digispark USB Development Board The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when...
AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V General information This is the good old AC Dimmer, but with 2 channels. This one also can control the alternating current voltage in the same way. It can be used with lamps, elements, fans, pumps, air cleaners etc. So it’s the same thing, but twice bigger. In the tutorial, you can...
Specifications: This card is compatible with NFC capable phones and tablets, it is Smart Card Tags. Frequency: 13.56 MHz 1K byte EEPROM memory (768 FREE BYTES availability) Size: 85mm x 54mm x 0.9mm Material: PVC, Waterproof Write endurance 100,000 cycle Reading distance is 0 - 10cm (Reading distance depends on readers, not the cards)
Dual USB 5V 1A 2.1A Mobile Power Bank 18650 Battery Charger PCB Power Module Accessories For Phone DIY New LED LCD Module Board
Description: A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!
Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S
4 x 4 Matrix Membrane Keypad Size: 7cm X 7.5cm 8 pin connector Adhesive mounting (sticker on the back side) Maximum Circuit Rating: 35VDC, 100mA Operation Temperature: 0 to +60 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours Fexible Circuit Length: Approx. 3.3 inch / 83 mm
1N4007 is a PN junction rectifier diode. These types of diodes allow only the flow of electrical current in one direction only. So, it can be used for the conversion of AC power to DC. 1N 4007 is electrically compatible with other rectifier diodes and can be used instead of any of the diode belonging to 1N400X series