

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Double-ended 50cm Cable Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.
5V LED Traffic Light Module
Click here to leave a review
Carlo Gavazzi Solid State Relays, RJ1A Series Item# RJ1A23D20U SSR SOLMINI 230V 20A 5-32VDC U
DC-DC 9V/12V/24V to 5V USB Step Down Power Module 2A
Brand: DFRobot
INTRODUCTION The APC220 radio module provides a simple and economic solution to wireless data communications. Integrates an embedded high speed microprocessor and high performance IC that creates a transparent UART/TTL interface, and elminates any
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: Sparkfun
Description: RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-20LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing. Power the...
Chip board ENC28J60-I/SOThe board 25MHZ crystalThe network interface board HR911105A3.3 V power supply pinThe board size : 56 (mm) x 34 (mm)
Product Name : DC Solenoid Electromagnet;Model : JF-0530B;Rated Voltage : DC 12V RatedCurrent : 300mA;Action Form : Pull Push Type;Rated Stroke & Force : 10mm, 5N Body Size : 30 x 15x 15mm/1.2"x 0.59"x 0.59"(L*W*H);Pluger Dia. : 56mm/ 2.2" Cable Length : 20cm/ 7.9";Material : Metal, Electronic Parts Weight : 32g;Package Content : 1 x DC Solenoid...
Description: This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on the other end with a mating socket. Compatible With: Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL...
Specifications: This card is compatible with NFC capable phones and tablets, it is Smart Card Tags. Frequency: 13.56 MHz 1K byte EEPROM memory (768 FREE BYTES availability) Size: 85mm x 54mm x 0.9mm Material: PVC, Waterproof Write endurance 100,000 cycle Reading distance is 0 - 10cm (Reading distance depends on readers, not the cards)
Specifications:Voltage: DC12VCurrent: 0.6AEnergized forms: intermittentUnlocking time: 1SSize: 27x29x18mm (L * W * H)
QUICK OVERVIEW 131 powerful instructions – Most Single Clock Cycle Execution 32 x 8 general purpose working registers Fully static operation Up to 20MIPS throughput at 20MHz On-chip 2-cycle multiplier Write/erase cycles: 10,000 flash/100,000 EEPROM Optional boot code section with independent lock bits In system programming by on-chip boot program True...
The TTP229 is capacitive sensing design specifically for touch pad controls. The device has a built in regulator for the touch sensor. Stable sensing method can cover diversity conditions. Interface control panel links through non-conductive dielectric material. The main application is focused at replacing of the mechanical switch or button.
Digispark USB Development Board The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when...
Reference: SparkFun
Description: A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!
5V LED Traffic Light Module