Reference: RBD-0188

USB Saleae Compatible 24MHz 8Channel Logic Analyzer Latest Support 1.1.15

Logical light indication: a small light indicate CHO electrical level. Input feature: 5PF,100K Ohm. USB power supply; USB logic analyzer for monitoring, analyzing and debugging digital circuits 8-Channels USB logic analyzer with a 24Mhz sampling frequency Can analyze UART, IIC, and SPI, etc automatically Great for MCU, ARM system and FPGA development...

Reference: RBD-1215

ATmega328P-PU PDIP-28 Microcontroller

131 powerful instructions – Most Single Clock Cycle Execution 32 x 8 general purpose working registers Fully static operation Up to 20MIPS throughput at 20MHz On-chip 2-cycle multiplier Write/erase cycles: 10,000 flash/100,000 EEPROM Optional boot code section with independent lock bits In system programming by on-chip boot program True read while write...

Reference: RBD-1537

EL Wire-White 3m With Pocket Inverter

Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter:  2mm EL light length: 3M Lifetime: >12,000 hours Color: White

Reference: RBD-2055

BLX-A Cover with Fuse Holder

Fuse Holder Material: Plastic Fuse Holder Insert Type Fuse Size: S Bolt Type Fuse Size: Small

Reference: RBD-0241

LM35 Temperature Sensor

Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical  LM35 (working) tested by...

Reference: RBD-0196

Brand: DFRobot

APC220 Radio Communication Module

INTRODUCTION The APC220 radio module provides a  simple and economic solution to wireless data communications. Integrates an  embedded high speed microprocessor  and high performance IC that creates a  transparent UART/TTL interface, and  elminates any

Reference: RBD-0349

Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board

Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection).RoboticsBD The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming...

Reference: RBD-0394

Slip Ring - 6 Wire (1.5A) max 240V

They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD

Reference: RBD-2236

20mm Piezo Ceramic Elements Sound Sensor

Plate Diameter: 20mm Element Diameter: 14mm Plate Thickness: .42mm Lead Length: ~50mm Plate Material: Brass Resonant Frequency (kHz): 6.3 +/- .6kHz

Reference: RBD-1333

Button Keypad 3x4 module (Assembled)

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-2085

PCB Mounted Passive Buzzer Module

Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH):  26 x 15 x 11 mm

Reference: RBD-2028

680uH 0.5W Color Ring Inductor

680uH (0.01mH) 1/2W Axial Lead Epoxy Coated Color Band Identifier Fixed Inductor

Reference: RBD-0767

Passive Buzzer 5V

Input Voltage(Max.) : 5V Resistance: 42 Ω Resonance Frequency: 2048 Hz Body Size : 12 x 8mm Pin Pitch: 6mm External Material: Plastic; Color: Black

Reference: RBD-0121

LED - SMD RGB HL5011 (Pack of 5)

Reference: RBD-0729

GPS Antenna 1575.42 MHz

Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male

Reference: RBD-0406

HW-411A LM2596 DC-DC Step Down Adjustable Power Supply Module 3A Max Buck Converter

Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD

Reference: RBD-2235

27mm Piezo Ceramic Elements Sound Sensor

Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Operating Temperature: -20~70 Clear sound Ultra-thin and lightweight Low power consumption for voltage type

Reference: RBD-0730

DC-DC Boost Module

The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;

Reference: RBD-0344

Weighing Sensor 24 Bit Load Cell Amplifier HX711

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD

Reference: RBD-1303

Battery Holder 6xAA

Cell Quantity: 6 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC Dimensions: 92 x 57 x 15 mm

Reference: RBD-0226

Brand: SparkFun Electronics

Camera Module - pcDuino V3 (2MP)

Camera Module - pcDuino V3 (2MP)

Reference: RBD-0623

DC-DC 9V/12V/24V to 5V USB Step Down Power Module 2A

Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD

Reference: RBD-2475

Mechanical Decade Counters Small Size 5 Counter

5 counters with 2 end caps are bundled togeatherbezel size 1.85" x 0.94" (for 5 counters with 2 end caps) mounting hole size 1.72" x 0.875" (for 5 counters with 2 end caps) total depth (from front of button to the edge of the PCB) 1.6" single counter width 0.32"

Reference: RBD-0132

TCRT5000L Reflective Optical Sensor

The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...

Reference: RBD-2317

5-way Tactile Navigation Switch

The  is a 4 way navigation switch (north, south, east, west) with a center push. Think of it as a mini joystick. Whilst the pins don’t align perfectly to a 2.54mm grid, it can be made to fit into a breadboard or perfboard by bending the pins.

Reference: RBD-1028

CD4026BE

IC Name: CD4026BE Package/Case: DIP-16

Reference: RBD-1539

EL Wire-Red 3m With Pocket Inverter

Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter:  2mm EL light length: 3M Lifetime: >12,000 hours Color: RED

Reference: RBD-0840

Veroboard Dot Type

Dimension: 14.5×6 cm Copper Thickness 1-4 OZ Board Thickness 1.1 mm Board color: Brown

Reference: RBD-0768

5 mm Red LED (Pack of 5)

Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent