- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Home Automation
- Learning Kit
- Arduino Shield & Module
- Robotics Parts
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- CNC & Laser Cutter
AA Battery Holder 3S
- Cell Quantity: 3
- Battery type: AA
- Storage temperature: 25ºC
- Max Operate temperature: 80ºC
Store Pickup Available!
Free Ship Over 5000 BDT
This 3 x 1.5V AA Battery Holder can hold 3 1.5V AA battery which can make 4.5 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells or it can also be used for one-time use and throw batteries for small DIY projects. The battery holder puts the batteries in series so that you have 3x the voltage of an AA battery. (approx. 4.5V)
It comes with a soldered open end wire.
Note: This product does not include a battery, you need to purchase it separately.
- Cell Quantity: 3.
- Battery type: AA.
- Storage temperature: 25ºC.
- Max Operate temperature: 80ºC.
- Wire Length: 120 mm.
- Mounting holes diameter: 3 mm.
- Color: Black.
|Max Operating temperature (ÂºC)||80|
|Storage temperature (ÂºC)||25|
|Wire Length (mm)||120|
|Mounting holes diameter (mm)||3|
|Shipment Weight||0.014 kg|
|Shipment Dimensions||8 × 5 × 3 cm|
1 x AA Battery Holder 3S
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series
Crystal 32.768KHz, matching capacitance 6pF DS1302 8-pin SMD homemade chips Seconds, Minutes, Hours, Day of Month, Day of Week, and Year Operating temperature: 0 degree — 70 degree
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
• Switching capacity available by 10A in spite of small size design for highdensity P.C. board mounting technique. • UL,CUL,TUV recognized. • Selection of plastic material for high temperature and better chemical solution performance. • Sealed types available. • Simple relay magnetic circuit to meet low cost of mass production.
INTRODUCTION The APC220 radio module provides a simple and economic solution to wireless data communications. Integrates an embedded high speed microprocessor and high performance IC that creates a transparent UART/TTL interface, and elminates any
AC-DC 5V 700mA 3.5W Precision Buck Converter AC 220V to 5v DC Step Down Transformer Power Supply Module
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
830 Solder-less Points Ideal for Experimenting With Circuit Design In Labs Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components Colored coordinates for easy components placement. Accept a variety of wire sizes 20-29 AWG
High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A
Model No.: ISR18650-1300 Capacity (mAh): 750-1300 (Copy) Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life Clone Battery Ampere cannot be accurately specified
Length: 5″. Pitch: 4.5″. Weight: 27 gm. Shaft Diameter: 5mm. Total length: 5 inch / 125 mm. Material: Poly-Carbonate.
Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust