- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
AA Battery Holder 2s
Store Pickup Available!
Free Ship Over 5000 BDT
2cell AA Battery Holder
The TTP229 is capacitive sensing design specifically for touch pad controls. The device has a built in regulator for the touch sensor. Stable sensing method can cover diversity conditions. Interface control panel links through non-conductive dielectric material. The main application is focused at replacing of the mechanical switch or button.
• Switching capacity available by 10A in spite of small size design for highdensity P.C. board mounting technique. • UL,CUL,TUV recognized. • Selection of plastic material for high temperature and better chemical solution performance. • Sealed types available. • Simple relay magnetic circuit to meet low cost of mass production.
The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
Description: This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board...
3S 11.1V 12.6V 25A W/Balance 18650 Li-ion Lithium Battery PCB Protection Board Specification: Brand newSize: about 56mm*45mm*1.2mmOver voltage range: 4.25-4.35v±0.05vOver discharge voltage range: 2.3-3.0v±0.05vMaximum operating current: 0-25AMaximum transient current: 34-40AQuiescent current: less than 30uA
Specification: Input voltage range：4～38VDC(Note:input voltage not exceeding 38V) Output voltage range：1.25-36VDC adjustable Output current: 0-5A, recommended for use in 4.5A. Output power: 75W Working temperature: -40~+85 degrees Operating frequency: 180KHz Efficiency:96%（max) Short circuit protection: yes(limit current 8A).
Brand: SparkFun Electronics
Raspberry Pi - Model B+ Enclosure (Black) Description: The Raspberry Pi Model B+ is THE new favorite of development platforms, so the last thing that you’d want is for something bad to happen to it. Why not protect it with one of these snazzy black plastic enclosures?
IR Transmitter - White (5mm) 5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)
This is a very compact DC-DC step-down converter capable of supplying any voltage between 1.23 and 30 V from a higher voltage power supply (up to 35 V).
4 x 4 Matrix Membrane Keypad Size: 7cm X 7.5cm 8 pin connector Adhesive mounting (sticker on the back side) Maximum Circuit Rating: 35VDC, 100mA Operation Temperature: 0 to +60 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours Fexible Circuit Length: Approx. 3.3 inch / 83 mm
Soldering is required