- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- Retired Products
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
74164 Shift Register
- IC 74LS164
- 8-bit Parallel-Out Serial Shift Register with Asynchronous Clear
- Package / Case: 14-DIP
Store Pickup Available!
Free Ship Over 5000 BDT
DS1302 Real Time Clock Module (DS1302Z clock chip,32.768KHZ crystal)
This Module is based on ISD1820, which a multiple-message record/playback device. It can offers true single-chip voice recording, no-volatile storage, and playback capability for 8 to 20 seconds. The sample is 3.2k and the total 20s for the Recorder.
Soldering is required
IR Infrared Remote Decoder Encoding Transmitter & Receiver Wireless Module
1N4007 is a PN junction rectifier diode. These types of diodes allow only the flow of electrical current in one direction only. So, it can be used for the conversion of AC power to DC. 1N 4007 is electrically compatible with other rectifier diodes and can be used instead of any of the diode belonging to 1N400X series
This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to...
EL wire is a thin copper wire coated in a phosphor that glows a 360 degree unbroken light when an alternating current is applied to it. It is bendable as a thin neon tube which makes it ideal for flexible decoration. It is great for car decoration, parties, camping and so on.
Chip board ENC28J60-I/SOThe board 25MHZ crystalThe network interface board HR911105A3.3 V power supply pinThe board size : 56 (mm) x 34 (mm)
The module has 12 push buttons. You can make usual keypads for enter numbers, symbols, or navigate and selections in the program. There are pull-up resistors of different values for each button. This makes it possible to connect all the 12 keys to taking only one analog port of the microcontroller. The button consists of two parts: a cap, which can be...
This is a very compact DC-DC step-down converter capable of supplying any voltage between 1.23 and 30 V from a higher voltage power supply (up to 35 V).
Specification: Input voltage range：4～38VDC(Note:input voltage not exceeding 38V) Output voltage range：1.25-36VDC adjustable Output current: 0-5A, recommended for use in 4.5A. Output power: 75W Working temperature: -40~+85 degrees Operating frequency: 180KHz Efficiency:96%（max) Short circuit protection: yes(limit current 8A).
4 x 4 Matrix Membrane Keypad Size: 7cm X 7.5cm 8 pin connector Adhesive mounting (sticker on the back side) Maximum Circuit Rating: 35VDC, 100mA Operation Temperature: 0 to +60 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours Fexible Circuit Length: Approx. 3.3 inch / 83 mm