Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2733
GY-50 L3G4200D 3-Axis Gyroscope Sensor Module Three selectable full scales (250/500/2000 dps) I2C and SPI digital output interface avail. Two I2C address you can select by jumpers 16 bit-rate value data output 8-bit temperature data output Wide supply voltage: 2.4 V to 3.6 V Low voltage-compatible IO (1.8 V) Embedded power-down and sleep...
Reference: RBD-2326
Brand: DFRobot
The DFRobot Heart Rate Monitor Sensor is used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG and output as an analog reading. An ECG signal can be extremely noisy so we have included an AD8232 chip which will generate a clear signal from the PR and QT Intervals. Using the Arduino IDE "Serial Plotter"...
Reference: RBD-2743
Wide supply voltage 1.71 V to 3.6 V Independent IO power (1.8V) and power supply voltage compatible Ultra-low power consumption of ± 2g / ± 4G / ± 6g / ± 8G / ± 16g IIC / SPI digital output interface 16-bit data output Programmable Embedded State Machine Embedded temperature sensor Embedded self-test Embedded FIFO 10,000 g high impact resistance
Reference: RBD-2745
The LSM9DS1 is a versatile, motion-sensing system-in-a-chip. It houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer – nine degrees of freedom (9DOF) in a single IC! The LSM9DS1 is equipped with a digital interface, but even that is flexible: it supports both I2C and SPI, so you’ll be hard-pressed to find a microcontroller it doesn’t...
Reference: RBD-2762
The GY-362 ADXL362 Sensor Module is a high-precision accelerometer module designed for a wide range of motion sensing applications. Powered by Analog Devices' ADXL362, this module offers ultra-low power consumption, exceptional accuracy, and versatile functionality.
Reference: RBD-2552
R503 Fingerprint Sensor is a device that allows you to read and save up to 200 fingerprints through a touch panel, it also contains a configurable LED light indicator. This sensor is small and easy to use, it has a wide detection range, a nut so you can install it easily and it has 6 pins, 2 for power, 1 for the finger detection signal, another for the...
Reference: RBD-2783
The GY-51 LSM303DLH chip has an accelerometer, magnetometer, A / D converters and signal conditioning circuit integrated. Still, the communication to the processor is done through the I2C bus. Thus only one chip is required to achieve a six-axis data detection and output. The LSM303DLH requires very little peripheral devices.
Reference: RBD-2561
Introducing the Fingerprint Recognition Sensor with UART TTL serial port—an easy-to-use biometric solution that can be seamlessly integrated into your projects. The Fingerprint Sensor Adapter module and the included 6-pin cable ensure compatibility with Arduino, making fingerprint detection and verification straightforward. This optical fingerprint sensor...
Reference: RBD-2792
This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor...
Reference: RBD-2710
Why is an analog eyeblink sensor better than a digital eyeblink sensor? Currently, most eye blink sensors on the market are digital. they can only distinguish between the eye being fully closed or fully open, unable to detect partial blinks or quick blinks. However, the analog sensor provides waveforms. By analyzing analog values, you can detect full...
Reference: RBD-2722
Add computer vision capabilities to your project, without the coding! The Person Sensor includes a camera module pre-programed and connected over Qwiic... Person Sensor V1.1 by Useful Sensors
Reference: RBD-2888
A sensor that allows you to measure your pulse with your finger using a phototransistor. The red LED lights up each time it detects a pulse. Powered by 5 V.
Reference: RBD-2918
EMG muscle sensor V3.0 with cable and electrodes Measures the electrical activity of muscles High signal quality for accurate and reliable measurement Adjustable gain and filtering for signal conditioning Compatible with various types of microcontrollers and data acquisition systems Comes with reusable electrodes and a 3.5mm jack cable for easy connection