Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2555
This is a self-contained switching module that energizes / de-energizes a relay based on the humidity level. Just add 5V power and hook up the load you want to control then adjust the potentiometer to set the relative humidity level at which you want the relay to switch between ON / OFF. This type of module can be used for applications such as to...
Reference: RBD-2420
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 °
Reference: RBD-2654
The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.
Reference: RBD-2443
The Collision Switch Module is used to detect a collision with an object or to detect the limit of travel.
Reference: RBD-2683
XH-M452 DC 12V LED Digital Thermostat Temperature Humidity Control Module The XH-M452 temperature and humidity control module is a versatile and precise solution for temperature and humidity regulation in various applications. With a power supply of DC 12V, this module offers reliable performance and accuracy. Key Specifications: Power supply: DC 12V...
Reference: RBD-2444
Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.
Reference: RBD-2728
Temperature controller module for both heating and cooling applications.
Reference: RBD-2445
Uses ultrasonic sound waves to detect obstacles and measure distance
Reference: RBD-2745
The LSM9DS1 is a versatile, motion-sensing system-in-a-chip. It houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer – nine degrees of freedom (9DOF) in a single IC! The LSM9DS1 is equipped with a digital interface, but even that is flexible: it supports both I2C and SPI, so you’ll be hard-pressed to find a microcontroller it doesn’t...
Reference: RBD-2446
This is the updated 2021 version of the HC-SR04 Ultrasonic Sensor, offering enhanced features and improved flexibility. Notably, the input voltage now ranges from 2.8V to 5.5V, providing compatibility with a wider range of microcontrollers, including both 3.3V and 5V systems. Mode 1: GPIO (General Purpose Input/Output) Mode 2: I2C (New Feature) Mode 3:...
Reference: RBD-2806
K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃
Reference: RBD-2507
Reference: RBD-2840
The DHT11 digital temperature and humidity sensor is a versatile composite sensor designed for accurate measurement of temperature and humidity levels. With its calibrated digital signal output and advanced sensing technology, the DHT11 ensures reliable performance and excellent long-term stability. This sensor features a resistive wet sensor and an NTC...
Reference: RBD-2543
The LPB40B Single-Point Ranging LiDAR based on the DToF principle. The DToF technology enables the laser radar to work stably under strong outdoor lighting, further improving the stability and accuracy of distance measurement. It is capable of withstanding up to 100klux of ambient light, with a range of up to 40m indoors and outdoors. The overall accuracy...
Reference: RBD-2841
The Humidity Sensor SYH-2R is an analog air humidity sensor designed to accurately measure humidity levels by changing resistance in response to varying humidity conditions. Operating within a wide range from 10% to 95% relative humidity (RH), this sensor provides reliable data on ambient moisture levels. The sensor module comes without a case, offering...
Reference: RBD-2553
Ultrasonic distance sensor determines the distance to a target by measuring time lapses between the sending and receiving of the ultrasonic pulse. This is an easy-to-use commercial-grade ultrasonic sensor module of high performance and reliability, featuring much smaller blind zone, wider sensing angle and a certain penetration power(smog, dust) compared...
Reference: RBD-2845
Waterproof analogue sensor with the high temperature working in the range from -200°C to 420°C. The output is resistance dependent on temperature. Probe length is 200 mm.
Reference: RBD-2661
The sensor reacts to an interruption in the beam of infrared light that is transmitted between the transmitter and receiver. When the beam is interrupted by another object, the receiver signals this event by lighting up. The module is equipped with a 3 mm IR LED with an illumination angle of 10°. Beam interruption systems are used e.g. in measuring gates.
Reference: RBD-2846
The DHT-11 Digital Temperature and Humidity Sensor is a compact and reliable sensor that can measure temperature and humidity with high accuracy. This sensor features a single-wire interface, making it easy to integrate with microcontrollers and other electronics projects. The DHT-11 has a temperature measurement range of 0°C to 50°C with an accuracy of...
Reference: RBD-2723
This acrylic mounting bracket fits the E18-D80NK Infrared Proximity sensor.
Reference: RBD-2892
Model: SNA118 Material: Plastic Plastic Type: PC Tool Supplies: CuttingDoes not Include ESP Wireless Module
Reference: RBD-2790
The US1881 is an integrated Hall-Effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A Hall-Effect sensor is much smaller, but can handle less current...
Reference: RBD-2799
This is the HC-SR04-33 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04-33 module includes an ultrasonic transmitter, a receiver and a control circuit. There are only four pins that you need to worry about on the HC-SR04: VCC...
Reference: RBD-2804
Operating Voltage(V): 5 ~24 Current Consumption Max: 5 mA Detection distance(mm): 5 mm. Type of detection: Inductive. Cable Length: 145 cm. Response Frequency: 500Hz Max. Protection class: IP 67.
Reference: RBD-2836
Operating Voltage: 3.5V-5V Supply Current: 15mA Optimal Sensing Distance: 3mm Designed with the reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn)
Reference: RBD-2763
Uses infrared to detect a reflective line on the floor.
Reference: RBD-2842
The QRE1113 breakout board offers a digital output solution, utilizing a capacitor discharge circuit to assess reflection levels. This compact board is designed for line sensing applications, particularly suitable when only digital I/O pins are available in the system. It is compatible with both 3.3V and 5V systems, providing versatility in various...
Reference: RBD-2848
Wireless proximity sensor activated magnetically. The device is used mainly to determine the position of doors and windows. Case dimensions - 11 x 16 mm.
Reference: RBD-2847
Wired proximity sensor activated magnetically. The device is used to determine the position of doors and windows. Case dimensions - 20 x 64 mm.
Reference: RBD-2891
The 40kHz 16mm ultrasonic sensor can detect objects in a certain area and gives the distance value between the sensor and the object. The sensor has an operating frequency of 40 KHz. 40 KHz signals propagate as sound waves in the direction of the target, and the reflected waves are detected by the sensor. Then, the distance measurement is made by...