Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2760
RS422 interface, two-way communication. B Y Z A ultra far transmission 1000 meters The module has ESD 15KV protection. Onboard to increase the limit of 10 ohms current limiting current protection. Module with TVS diode. Anti lightning, peak voltage. The module has 120-ohm termination resistors, which can effectively reduce the interference of long-range...
Reference: RBD-2761
ICL8038 12V to 15V, Signal Generator, Medium/Low Signal, Frequency 10Hz-450KHz, Triangular/Rectangular/Sine Wave Generator, Module Working voltage: 12V ~ 15V Output: Triangular wave, Square wave and sine wave. Frequency range: 10HZ ~ 450kHz Low distortion sine wave: 1% Duty cycle range: 2% to 98% Low temperature drift: 50ppm / ℃ Triangular wave output...
Reference: RBD-2798
Add another eight pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two I2C pins which can be shared with other I2C devices, and in exchange gives you eight general purpose pins. You can set each of eight pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any...
Reference: RBD-2832
Designed for use as an endstop for 3D printers but it can be used for other contact detection applications as well.
Reference: RBD-2833
Type: Vibration Sensors Output: Switching Transducer Dimensions: 25 x 14 x 6 (LxWxH) mm Weight: 3 gm
Reference: RBD-2834
Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.
Reference: RBD-2857
Brand: DFRobot
The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application engineers. This medium-power high-efficiency solar power management module allows you to charge a 12V lead-acid battery with a maximum of 4A using a...
Reference: RBD-2856
Brand: DFRobot
The DFRobot Solar Power Manager series are designed for IoT projects and renewable energy projects, providing safe and high-efficiency embedded solar power management modules for makers and application engineers. Solar Power Manager 5V is a small power and high-efficiency solar power management module designed for 5V solar panel. It features as MPPT...
Reference: RBD-2858
Multi-Sensor Support: Works with various sensors like NTC thermistors, TCRT5000 line followers, and force sensors. Precise Control: Dual potentiometers for fine-tuning sensor thresholds. Wide Voltage Compatibility: LM393 chip ensures adaptability to diverse power sources. Compact & Durable Design: Integrates seamlessly into projects with a robust build.
Reference: RBD-2919
This mono Class D amplifier module with a surprisingly compact form factor - less than 2cm on a side - uses a MAX98357 chip to deliver 3W of power. Its I2S input allows an easy association with a Raspberry Pi or ESP32, allowing for example to design a small portable amplified speaker.
Reference: RBD-2920
Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.
Reference: RBD-2921
Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.
Reference: RBD-2922
Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: I2C Communication Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.
Reference: RBD-2923
Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: I2C Communication Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.
Reference: RBD-2925
125 Channels, Multi-point communication, and frequency hopping to meet the communication needs Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power-down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch Interface for embedded applications size: 34mm X 17mm X 1mm
Reference: RBD-2928
Radio module (transmitter and receiver) operating in 433 MHz band with SPI communication interface. Powered by 2.7 V - 3.3 V, the outputs are goldpin connectors.It has an external antenna with SMA connector.
Reference: RBD-2939
Brand: DFRobot
RS485 is an industrial standard for long-distance, anti-interference, and reliable communication. The Arduino RS485 shield, specially designed for the Arduino Uno board. It converts UART/Serial protocol to the RS485 protocol. This RS485 board allows Arduino talk to industrial devices. In contrast to RS-422, which has a single driver circuit that cannot...
Reference: RBD-2940
The MOSFET F5305S 4-Channel Pulse Trigger Switch Controller is a versatile and robust module designed for controlling high-power devices through PWM input. This controller is perfect for managing the speed of motors, adjusting the brightness of light bulbs, and other applications requiring precise control. Based on the reliable F5305S MOSFET model, this...