Reference: RBD-2061

Flat Ribbon 2.54MM Pitch FC-6 JTAG ISP AVR Data Cable 20cm 6 Pin

Compatible with all embedded systems platforms. Supports field updates and troubleshooting. Pins: 6. Cable length: 200mm. Cable size: 28 AWG.

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-2062

Flat Ribbon 2.54MM Pitch FC-8 JTAG ISP AVR Data Cable 20cm 8 Pin

Compatible with all embedded systems platforms. Supports field updates and troubleshooting. Pins: 8. Cable length: 200mm. Cable size: 28 AWG.

Reference: RBD-2063

Flat Ribbon 2.54MM Pitch FC-10 JTAG ISP AVR Data Cable 20cm 10 Pin

Compatible with all embedded systems platforms. Supports field updates and troubleshooting. Pins: 10. Cable length: 200mm. Cable size: 28 AWG.

Reference: RBD-0400

NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs

16 reviews

Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....

Reference: RBD-1952

Banana Plug To Test Hook Clip Probe Cable For Multimeter/Power Supply Test Equipment

2 reviews

Digital Multi Meter Banana Plug To Test Hook Clip Probe Cable Length: 1 Meter Voltage: 1000V 20A Weight: 43g

Reference: RBD-0413

Data Logger Module Logging Shield Data Recorder Shield for Arduino

2 reviews

SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...

Reference: RBD-1406

Cable - 30 cm servo extension

High-Quality cable One male and one female connector. Flat 30cm Servo Lead Extention (JR) Quality wire and connectors used. Great for larger planes with servos that experience high loads.

Reference: RBD-0433

I2C LCD Adapter Module

40 reviews

5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.

Reference: RBD-0941

Servo Extension Cable Male to Female 300mm

7 reviews

High-Quality cable One male and one female connector. Flat 25 cm Servo Lead Extension (Futaba) Quality wire and connectors used. Great for larger planes with servos that experience high loads.

Reference: RBD-0438

New ENC28J60 Ethernet LAN Network Module For Arduino

5 reviews

ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD

Reference: RBD-0443

GPRS GSM SIM900 Arduino Shield

7 reviews

Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-0550

Voice Recognition Module Kit V3 (Elechouse)

5 reviews

Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD

Reference: RBD-0553

FPM10A Optical Fingerprint Reader Sensor Modules (With Shield)

3 reviews

Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds

Reference: RBD-0579

GPS GSM GPRS SIM808 Module (Arduino Compatible)

1 review

Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep...

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

9 reviews

CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1

Reference: RBD-0702

1 Channel 5V Relay Board Module

49 reviews

It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock

Reference: RBD-2398

4 Pin JST-PH 2mm Cable–Female/Female - 150mm/6" Long

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices

Reference: RBD-0703

SSC-32 32Ch Servo Controller Lynxmotion Compatible

Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts

Reference: RBD-2399

4 Pin JST-XH 2.54mm Cable–Female/Female - 150mm/6" Long

1 review

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-XH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices

Reference: RBD-0323

Arduino Uno R3 SMD

42 reviews

Microcontroller ATmega328 (SMD) – Interface CH340G Operating Voltage: 5V Input Voltage (recommended): 7-12V Digital I / O Pins 14 (of which 6 provide PWM output) RoboticsBD Analog Input Pins: 6 A programming cable is included.

Reference: RBD-2425

Shielded Blue USB Type-C Cable 30cm for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-0742

Motor Driver 43A BTS7960

9 reviews

Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.

Reference: RBD-2427

USB Type-C Cable 1meter for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-0832

Arduino MicroSD Card Module

33 reviews

Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g

Reference: RBD-2430

6 Pin JST XH Cable Connector Female to Open - 2.54mm Pitch 20cm

This 6-wire cable has a length of slightly over 20cm and is equipped with JST-PH female 6-pin connectors at one ends. Such JST cables are frequently used with compact rechargeable battery packs, RC receivers and transmitters, miniature cameras, and other small electronic devices.

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-0904

Solderable Cable Red and Black Pair

5 reviews

Pair of wires for soldering with DC motors DC applications, breadboards, electronics, and robotics DIY projects Length: 120mm

Reference: RBD-0699

1.8" inch TFT LCD Display module ST7735S 128x160

2 reviews

Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI

Reference: RBD-2615

1 Meter Twisted Electrical Flexible Wire - Red Black

3 reviews

Flexible-SC(FR) cable with 1x0.4 rm gauge size, red & black color, and flame-retardant insulation material. Designed for electrical use in a variety of applications.

Reference: RBD-0576

STM8S103F3P6 ARM STM8 Minimum System Development Board Module (Arduino Compatible)

Chipboard STM32F103C8T6 On board, SWIM interface and reset button Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V. Power light and the Demo indicator light Leads all the pins and has detailed label for the Pins. Support SWIM debug mode. RoboticsBD