Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1158
Width: 10 mm Length: About 33m. Type: Polyimide Tape. Heat Resistance: 200℃. Thickness Tolerance: ±10% . One-side Self-adhesive.
Reference: RBD-0296
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 75 mm Width : 15 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow 1 pcs
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0315
Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm. RoboticsBD
Reference: RBD-0319
Type K Type. Mounting thread: M6 Temperature Range:0-600°C. RoboticsBD
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-2309
Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! This module contains an ESP8285, which is an ESP8266 processor with 1MB of FLASH memory already built in. You can use it just like an ESP8266, it's the same processor and WiFi The ESP8266 processor from Espressif is an 80 MHz microcontroller with a...
Reference: RBD-0355
Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line
Reference: RBD-0358
Dimensions: 11×15 x 2 (L x W x H) mm Weight: 1gm Mutual transform between 5V TTL and 3.3V TTL Two channels of logic and high voltage low voltage logic can two-way transform Portable and lightness, with 2 rows 4 pin contact pins
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-2651
D1 Mini board with 4 MB flash memory and ESP8266 chipset. The board can be programmed with Arduino IDE, has the CH340 USB chipset and allows you to create IoT devices quickly and easily.
Reference: RBD-2652
Firstly, In terms of pins, the D1 Mini and NodeMCU V3 development boards are quite similar. They both break out all ESP8266 ESP-12E/F pins. The NodeMCU V3 board has additional 3V3 and GND pins. Hence, it is more suitable for various connections to devices with an additional button for the flash. A high-quality USB cable is essential for this board to...
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-0414
A probe by new original installation import DS18B20 temperature sensor chip. RoboticsBD Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof. Stainless steel tube encapsulation waterproof moistureproof prevent rust. Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use...
Reference: RBD-0415
Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient. RoboticsBD
Reference: RBD-2892
Model: SNA118 Material: Plastic Plastic Type: PC Tool Supplies: CuttingDoes not Include ESP Wireless Module
Reference: RBD-0563
Overcharging and Over Discharging Protection Short circuit protection: Yes Applicable assembly: Nominal 4.5V Batteries / 3 strings. RoboticsBD
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0741
Frequency Range: 433 MHZ ASK /OOK modulation mode Super anti-power interference Low-power sleep less than 1uA Low self-radiation Small size Frequency stability and reliability Various international testing standards
Reference: RBD-0905
Bluetooth protocol: Bluetooth Specification v2.0+EDR. Frequency: 2.4GHz ISM band. Modulation: GFSK(Gaussian Frequency Shift Keying). Emission power: =4dBm, Class 2. Sensitivity: =-84dBm at 0.1% BER. RoboticsBD
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-0922
Dimensions: 91 x 21 x 30 mm(LxWxH) Weight: 18 gm. Voltage: 3.3V or 5V. Port: Analog. Resistance: 10K. Appn: Raspberry-Pi projects. DIY projects., Arduino projects.