Reference: RBD-0151

Angle Sensor Module for Arduino SW-520D

1 review

Operating voltage 3.3V-12V A fixed bolt hole for easy installation Wide voltage LM393 comparator Maximum output current: 15mA Can work on low voltages

Reference: RBD-0662

EasyDriver Shield Stepper Motor Driver V44 A3967 For Arduino

Power supply: 7V to 30V. The higher the voltage, the higher the torque at high speeds. Adjustable current control from 150mA/phase to 750mA/phase. Logic voltage: 5V or 3.3V. A3967 microstepping driver. RoboticsBD

Reference: RBD-1830

FT245+CPLD High Speed Program Altera USB Blaster Download Cable FPGA / CPLD Downloader

FT245+CPLD High-Speed Program Altera USB Blaster Download Cable FPGA / CPLD Downloader

Reference: RBD-0152

SW-420 NC Type Vibration Sensor Module

10 reviews

Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation

Reference: RBD-0684

Motor Driver - Dual TB6612FNG (1A)

9 reviews

CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1

Reference: RBD-2142

CH340C WIFI Module Adapter Download Debug for ESP8266 ESP-01/01S

2 reviews

Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.

Reference: RBD-0156

TCS230 TCS3200 Color Sensor Recognition Module

7 reviews

Operating Voltage: 3V-5V High-resolution conversion of light intensity to frequency. Chip pins all has drawn for standard 100. Put the needle (2.54 mm). Mil-convenient for bitmap board. Programmable color and full-scale output frequency. Communicate directly with a microcontroller. Low-profile surface mount package.

Reference: RBD-0703

SSC-32 32Ch Servo Controller Lynxmotion Compatible

Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts

Reference: RBD-2160

1 Meter Micro USB Cable for Arduino, Node MCU and Flight Controllers

4 reviews

Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.

Reference: RBD-0222

35mm Piezo Ceramic Elements Sound Sensor

14 reviews

Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound

Reference: RBD-0742

Motor Driver 43A BTS7960

9 reviews

Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.

Reference: RBD-2162

1 Meter Mini USB Cable for Arduino Nano

1 review

USB Type: Type-A to Mini-B Length: 1 meter/ 3.2 Feet Exclusively designed for Arduino boards.  Compatible with Arduino Nano Larger Cable

Reference: RBD-0150

5mW Adjustable Laser Dot Diode Module

34 reviews

Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~＋40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser

Reference: RBD-1606

L297 Stepper Motor Controller IC

Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C

Reference: RBD-1761

Cable For Arduino UNO/MEGA (USB A to B)-3.2 Feet/1Meter

6 reviews

USB Type: Type-A to Type-B Weight: 80 gm. Length: 1m / 3.2Feet Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.

Reference: RBD-0313

RC522 RFID Card Reader Module Kit Android NFC supported

46 reviews

Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz

Reference: RBD-1678

Big Easy Driver - Stepper Motor Driver

2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module

Reference: RBD-2195

50 cm Micro USB Cable for Arduino Leonardo and Node MCU

3 reviews

Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.

Reference: RBD-0241

LM35 Temperature Sensor

31 reviews

Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical  LM35 (working) tested by...

Reference: RBD-1635

Dual Channel Motor Driver Shield For Arduino

Logic control, 5V from Arduino main board Polarity protection for External motor power input 2 fast test buttons for each motor channel Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source) Up to 2A current each channel Pin 4, 5,6,7 are used to drive two DC motor Support PWM speed control Support  advance speed control

Reference: RBD-2196

50 cm Cable For Arduino UNO/MEGA (USB A to B)

3 reviews

USB Type: Type-A to Type-B Weight: 26 gm. Length: 50 cm Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.

Reference: RBD-0272

Brand: Waveshare

Logic Level Converter

1 review

Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion  level  range:  1.8 V-6 V Instructions for use:  (3.3 V,  5 V  to  each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V  power supply  (can  be an external  5V power supply)

Reference: RBD-1724

DC-5V-35V 5A PWM Motor Speed Controller

2 reviews

Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.

Reference: RBD-2198

CH341 USB Programmer

Model: CH341 Series Main Chip: CH341B Dimensions in mm (LxWxH): 85 x 28 x 12 Weight (gm): 20 8-bit parallel in EPP or MEM mode

Reference: RBD-0288

GY-801 - Multi Sensor Board

1 review

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-1810

L293D Shield for NodeMCU V2

1 review

Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver

Reference: RBD-2311

USB To Serial Cable TTL 4 Pin Rs 232 UART Converter Adapter Programming Module

1 review

USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.

Reference: RBD-0311

YF-S201 Hall Effect Water Flow Meter / Sensor

9 reviews

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD

Reference: RBD-1912

L293D Motor Driver Module

1 review

New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)

Reference: RBD-2315

Pogo Pin Probe Clip - 6 Pins with 2.54mm

1 review

Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm

Reference: RBD-0312

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

1 review

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

Reference: RBD-2145

L298P Motor Driver Shield for Arduino

L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators